Poulan PDGT26H48C owner manual Mowing Tips, Purge Transmission, Automatic Transmission Warm UP

Page 15

OPERATION

•Remove retainer spring from the drive belt tension handle to relieve belt tension.

•Start engine and allow it to warm up for three (3) min- utes.

•Shut-off engine and engage parking brake.

•Engage drive belt tension handle and replace the retainer spring.

AUTOMATIC TRANSMISSION WARM UP

•Before driving the unit in cold weather, the transmission should be warmed up as follows:

•Be sure the tractor is on level ground.

•Place the motion control lever in neutral. Re- lease the parking brake and let the brake slowly return to operating position.

•Allow one minute for transmission to warm up. This can be done during the engine warm up period.

•The attachments can be used during the engine warm- up period after the transmission has been warmed up and may require the choke control be pulled out slightly.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

PURGE TRANSMISSION

CAUTION: Never engage or disengage freewheel lever while the engine is run-

ning.

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de- veloped during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

•Place tractor safely on level surface with engine off and parking brake set.

•Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual).

•Sitting in the tractor seat, start engine. After the en- gine is running, move throttle control to slow position. Disengage parking brake

•Move motion control lever to full forward position and hold for five (5) seconds. Move lever to full reverse position and hold for five (5) seconds. Repeat this procedure three (3) times.

NOTE: During this procedure there will be no movement of drive wheels. The air is being removed from hydraulic drive system.

•Move motion control lever to neutral (N) position. Shut- off engine and set parking brake.

15

•Engage transmission by placing freewheel control in driving position (See “TO TRANSPORT” in this section of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. Disengage parking brake.

•Slowly move motion control lever forward, after the tractor moves approximately five (5) feet, slowly move motion control lever to reverse position. After the trac- tor moves approximately five (5) feet return the mo- tion control lever to the neutral (N) position. Repeat this procedure with the motion control lever three (3) times.

•Your tractor is now purged and now ready for normal operation.

MOWING TIPS

•Tire chains cannot be used when the mower housing is attached to tractor.

•Mower should be properly leveled for best mowing per- formance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

•The left hand side of mower should be used for trim- ming.

•Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the tractor. This will result in a more even distribution of clippings and more uniform cutting.

•When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 12).

00272

FIG. 12

•If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.

•Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

•Always operate engine at full throttle when mow- ing to assure better mowing performance and proper discharge of material. Regulate ground speed by se- lecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

•When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

Page 14 Page 16
Image 15
Page 14 Page 16
Contents PDGT26H48C II. Slope Operation IV. ServiceSafe Operation Practices for RIDE-ON Mowers General OperationTable of Contents Customer Responsibilities Product SpecificationsUnassembled Parts To Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See FigsCheck Tire Pressure Check Mower LevelnessCheck for Proper Position of ALL Belts Operation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelMowing Tips Purge TransmissionAutomatic Transmission Warm UP Maintenance General RecommendationsBefore Each USE Tractor Transaxle Pump Fluid EngineBelts Transaxle CoolingCleaning Service and Adjustments To Install MowerTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Secondary Drive Belt See Fig To Replace Mower Drive BeltTransmission REMOVAL/REPLACEMENT To Adjust Attachment Clutch See FigTo Check and Adjust Brake Transaxle Motion Control Lever Neutral Adjustment See FigTo Remove Wheel for Repairs To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERInterlocks and Relays To Adjust Throttle Control CableTo Adjust Choke Control To Adjust Carburetor To Replace Headlight BulbCylinders OtherFuel System Engine OILProblem Cause Correction Troubleshooting PointsWith attachment clutch Tractor Model Number PDGT26H48C SchematicElectrical KEY Part Description Chassis and Enclosures 183569 Bracket Asm., Fender 153 Ground DriveTransaxle Hydro Gear Steering Assembly 180656 Wheel, Steering Engine KEY Part NO. NO. Description Lift Assembly Repair Parts Seat Assembly Wheels & Tires DecalsMower Deck KEY Part NO. NO. Description Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PDGT26H48C specifications

The Poulan PDGT26H48C is a versatile and robust lawn tractor designed for homeowners seeking efficiency and performance in lawn maintenance. With its powerful engine and durable construction, it stands out in the lawn care market, making it a reliable choice for mowing larger yards.

At the heart of the PDGT26H48C is a 26-horsepower Briggs & Stratton engine, known for its reliability and fuel efficiency. This engine provides ample power for tackling tough mowing tasks, and the automatic transmission ensures smooth acceleration and easy handling. The responsive controls contribute to an enjoyable mowing experience, allowing users to maneuver around obstacles with ease.

One of the key features of the Poulan PDGT26H48C is its 48-inch cutting deck, which allows for wide cutting swath and faster mowing. The deck is designed with three adjustable blades, providing a clean and even cut regardless of the grass type or terrain. With cutting height adjustments ranging from 1 to 4 inches, users can customize their mowing height for optimal results throughout the growing season.

The lawn tractor incorporates a versatile bagging and mulching system. The included rear bagger collects clippings for easy disposal, while the mulching option finely chops the grass to return nutrients to the soil, promoting a healthy lawn ecosystem. This adaptability makes the PDGT26H48C suitable for various mowing preferences.

Additionally, the tractor is equipped with large, rugged wheels that provide excellent traction and stability on uneven terrain. The comfortable high-back seat ensures ease of use during longer mowing sessions, while the ergonomic design allows for reduced operator fatigue.

Another notable characteristic is the convenient front-mounted headlights, which extend usability into the early morning or late evening hours. This feature is particularly beneficial during busy seasons when time is of the essence.

Overall, the Poulan PDGT26H48C represents a blend of power, comfort, and innovative features, making it a valuable tool for homeowners looking to maintain their lawns efficiently. Whether tackling large lawns or navigating tricky landscaping, this lawn tractor promises reliability and ease of use.
Top Page Image Contents