Poulan PDGT26H48C owner manual To Level Mower Housing, FRONT-TO-BACK Adjustment See Figs

Page 21

SERVICE AND ADJUSTMENTS

•Engage belt tension rod by pushing rod into locking bracket.

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly.

•Connect anti-sway bar to chassis bracket under left footrest and retain with double loop retainer spring.

•If equipped, turn height adjustment knob clockwise to remove slack from mower suspension.

•Raise deck to highest position.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 20 and 21)

•Raise mower to its highest position.

•Measure height from bottom edge of mower to ground level at front corners of mower. Distance “A” on both sides of mower should be the same.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

 

OF MOWER TO

GROUND

00598

GROUND

 

 

A

GROUND LINE

A

 

 

FIG. 20

FRONT-TO-BACK ADJUSTMENT (See Figs. 22 and 23)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is approximately 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

Check adjustment on right side of tractor. Position any blade so the tip is pointing straight forward. Measure distance "B" at front and rear tip of the blade.

•Before making any necessary adjustments, check that both front plate links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of blade, loosen nut “C” on both front links an equal number of turns.

NOTE: Each full turn of nut “C” will change distance. “B” by approximately 3/16".

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•To raise front of blade, loosen nut “D” from trunnion on both front links. Tighten nut “C” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•Recheck side-to-side adjustment.

02548

BLADE

“B”“B”

FIG. 22

BOTH FRONT PLATE LINKS MUST BE

EQUAL IN LENGTH

SUSPENSION

ARM

01553

LIFT LINK ADJUSTMENT NUT

FIG. 21

02516

NUT “D”

02517

FRONT PLATE

ASSEMBLY

NUT “C”

TRUNNION

FIG. 23

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents PDGT26H48C Safe Operation Practices for RIDE-ON Mowers IV. ServiceGeneral Operation II. Slope OperationTable of Contents Customer Responsibilities Product SpecificationsUnassembled Parts Tools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See FigsCheck Tire Pressure Check Mower LevelnessCheck for Proper Position of ALL Belts Operation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP Maintenance General RecommendationsBefore Each USE Tractor Belts EngineTransaxle Cooling Transaxle Pump FluidCleaning Service and Adjustments To Install MowerTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Secondary Drive Belt See Fig To Replace Mower Drive BeltTo Check and Adjust Brake To Adjust Attachment Clutch See FigTransaxle Motion Control Lever Neutral Adjustment See Fig Transmission REMOVAL/REPLACEMENTTo Start Engine with a Weak Battery See Fig To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER To Remove Wheel for RepairsTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight Bulb Interlocks and RelaysFuel System OtherEngine OIL CylindersProblem Cause Correction Troubleshooting PointsWith attachment clutch Tractor Model Number PDGT26H48C SchematicElectrical KEY Part Description Chassis and Enclosures 183569 Bracket Asm., Fender 153 Ground DriveTransaxle Hydro Gear Steering Assembly 180656 Wheel, Steering Engine KEY Part NO. NO. Description Lift Assembly Repair Parts Seat Assembly Wheels & Tires DecalsMower Deck KEY Part NO. NO. Description Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PDGT26H48C specifications

The Poulan PDGT26H48C is a versatile and robust lawn tractor designed for homeowners seeking efficiency and performance in lawn maintenance. With its powerful engine and durable construction, it stands out in the lawn care market, making it a reliable choice for mowing larger yards.

At the heart of the PDGT26H48C is a 26-horsepower Briggs & Stratton engine, known for its reliability and fuel efficiency. This engine provides ample power for tackling tough mowing tasks, and the automatic transmission ensures smooth acceleration and easy handling. The responsive controls contribute to an enjoyable mowing experience, allowing users to maneuver around obstacles with ease.

One of the key features of the Poulan PDGT26H48C is its 48-inch cutting deck, which allows for wide cutting swath and faster mowing. The deck is designed with three adjustable blades, providing a clean and even cut regardless of the grass type or terrain. With cutting height adjustments ranging from 1 to 4 inches, users can customize their mowing height for optimal results throughout the growing season.

The lawn tractor incorporates a versatile bagging and mulching system. The included rear bagger collects clippings for easy disposal, while the mulching option finely chops the grass to return nutrients to the soil, promoting a healthy lawn ecosystem. This adaptability makes the PDGT26H48C suitable for various mowing preferences.

Additionally, the tractor is equipped with large, rugged wheels that provide excellent traction and stability on uneven terrain. The comfortable high-back seat ensures ease of use during longer mowing sessions, while the ergonomic design allows for reduced operator fatigue.

Another notable characteristic is the convenient front-mounted headlights, which extend usability into the early morning or late evening hours. This feature is particularly beneficial during busy seasons when time is of the essence.

Overall, the Poulan PDGT26H48C represents a blend of power, comfort, and innovative features, making it a valuable tool for homeowners looking to maintain their lawns efficiently. Whether tackling large lawns or navigating tricky landscaping, this lawn tractor promises reliability and ease of use.
Top Page Image Contents