Poulan PD25PH48STE owner manual To Level Mower Housing, FRONT-TO-BACK Adjustment See Figs

Page 21

SERVICE AND ADJUSTMENTS

•Position front plate assembly between front mower brackets. Raise deck and plate assembly to align holes and insert flanged pins. Secure pins with double loop retainer springs between the plate assembly and mower brackets.

NOTE: To assist in locating hole in flanged pin, the hole in pin is inline with notch on head of pin. If necessary, move mower side-to-side to give space between plate and mower brackets.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

•Engage belt tension rod by pushing rod into locking bracket.

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly.

•Connect anti-sway bar to chassis bracket under left footrest and retain with double loop retainer spring.

•If equipped, turn height adjustment knob clockwise to remove slack from mower suspension.

•Raise deck to highest position.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 19 and 20)

•Raise mower to its highest position.

•Measure height from bottom edge of mower to ground level at front corners of mower. Distance “A” on both sides of mower should be the same.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

00598

OF MOWER TO

GROUND

 

GROUND

A

GROUND LINE

A

FIG. 19

SUSPENSION ARM

LIFT LINK ADJUSTMENT NUT

01553

FRONT-TO-BACK ADJUSTMENT (See Figs. 21 and 22)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is approximately 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

Check adjustment on right side of tractor. Position any blade so the tip is pointing straight forward. Measure distance "B" at front and rear tip of the blade.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of blade, loosen nut “C” on both front links an equal number of turns.

NOTE: Each full turn of nut “C” will change distance. “B” by approximately 3/16".

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•To raise front of blade, loosen nut “D” from trunnion on both front links. Tighten nut “C” on both front links an equal number of turns.

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•Recheck side-to-side adjustment.

02548

MANDREL

“B”“B”

FIG. 21

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

02516

TRUNNION

NUT “D”

FRONT PLATE

NUT “C”

02517

ASSEMBLY

 

FIG. 20

FIG. 22

 

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents PD25PH48STE Safety Rules Safety Rules Table of Contents Steering Wheel Gauge Wheels Unassembled PartsSeat Nose Roller MowerTools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See FigsCheck Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP Lubrication Chart MaintenanceGeneral Recommendations Before Each USETractor Engine Cleaning Service and Adjustments To Install MowerTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Secondary Drive Belt See Fig To Replace Mower Drive BeltTo Check and Adjust Brake See Fig Transmission REMOVAL/REPLACEMENTTo Replace Motion Drive Belt See Fig To Start Engine with a Weak Battery See Fig To Adjust Steering Wheel ALIGN- MentReplacing Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsWith attachment clutch Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation For Service or Replacement Parts Parts and Service

PD25PH48STE specifications

The Poulan PD25PH48STE is a standout in the realm of lawn care, known for its power, efficiency, and user-friendly design. This riding mower is engineered for homeowners who seek a reliable and robust machine capable of handling larger lawns with ease and precision.

At the heart of the PD25PH48STE is a strong 25 horsepower Briggs & Stratton engine. This powerful engine ensures smooth operation and can tackle tough grass and uneven terrain without straining. Equipped with a hydrostatic transmission, this mower provides seamless speed control and a responsive driving experience. Operators can easily adjust their speed without hassle, which is particularly beneficial for navigating around obstacles in the yard.

One of the exceptional features of the Poulan PD25PH48STE is its 48-inch cutting deck. This wide cutting deck allows for increased productivity, as it enables users to cover more ground in less time. The deck is designed with three precision blades, promoting an even cut while reducing the likelihood of grass clumping. Furthermore, the cutting height can be easily adjusted, ranging from 1 to 4 inches, allowing users to customize their mowing experience according to their lawn conditions.

Another notable attribute of the PD25PH48STE is its comfortable and ergonomic seating. The high-back seat provides ample support, making long mowing sessions more enjoyable. Additionally, the design features a user-friendly dashboard, where operators can control the mower's various functions and monitor engine performance at a glance.

Safety is also a top priority with this model. The PD25PH48STE includes essential safety features such as an auto shut-off function that activates when the operator leaves the seat, protecting against accidental injuries. The robust frame is built to withstand the rigors of lawn care while ensuring stability and durability.

Moreover, the Poulan PD25PH48STE supports innovative technologies, including a maintenance-free battery and easy-access grease fittings for straightforward upkeep. This design focus guarantees the mower's longevity, allowing owners to invest in a product that will serve them well for years to come.

In summary, the Poulan PD25PH48STE is a reliable riding mower that combines power, versatility, and user-friendly features. Its robust engine, wide cutting deck, and safety-focused design make it an ideal choice for homeowners seeking to maintain their lawns efficiently. As a trusted name in outdoor equipment, Poulan continues to deliver quality products that enhance the mowing experience.
Top Page Image Contents