Poulan PD25PH48STE To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills

Page 13

OPERATION

The cutting height range is approximately 1-1/2" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•Remove retainer spring and clevis pin which secure each gauge wheel bar.

•Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

•Replace retainer spring into clevis pin.

•Be sure all gauge wheels are in the same setting.

IMPORTANT:BE SURETO READJUST GAUGEWHEELS IFYOU CHANGE THE CUTTING HEIGHT OF THE MOWER DECK.

RETAINER

SPRING

019

77

 

CLEVIS

PIN

FIG. 9

TO OPERATE MOWER (See Fig. 10)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut.

•Lower mower with attachment lift control.

•Start mower blades by engaging attachment clutch

control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.

PULL OUT TO

ATTACHMENT LIFT LEVER HIGH POSITION

"ENGAGE"

 

 

 

 

LOW

 

 

POSITION

ATTACHMENT

 

 

CLUTCH SWITCH

 

 

PUSH IN TO

 

 

"DISENGAGED"

 

 

DEFLECTOR SHIELD

02142

 

FIG. 10

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If stopping is absolutely necessary, push brake pedal quickly to brake position and engage parking brake.

•To restart movement, slowly release parking brake and brake pedal.

•Slowly depress appropriate drive pedal to slowest set- ting.

•Make all turns slowly.

TO TRANSPORT (See Figs. 7 and 11)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

•Raise attachment lift to highest position with attachment lift control.

•Pull freewheel control out and into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents PD25PH48STE Safety Rules Safety Rules Table of Contents Steering Wheel Gauge Wheels Unassembled PartsSeat Nose Roller MowerTools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See FigsCheck Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP Lubrication Chart MaintenanceGeneral Recommendations Before Each USETractor Engine Cleaning To Install Mower Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Secondary Drive Belt See Fig To Replace Mower Drive BeltTransmission REMOVAL/REPLACEMENT To Check and Adjust Brake See FigTo Replace Motion Drive Belt See Fig To Start Engine with a Weak Battery See Fig To Adjust Steering Wheel ALIGN- MentReplacing Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsWith attachment clutch Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation For Service or Replacement Parts Parts and Service

PD25PH48STE specifications

The Poulan PD25PH48STE is a standout in the realm of lawn care, known for its power, efficiency, and user-friendly design. This riding mower is engineered for homeowners who seek a reliable and robust machine capable of handling larger lawns with ease and precision.

At the heart of the PD25PH48STE is a strong 25 horsepower Briggs & Stratton engine. This powerful engine ensures smooth operation and can tackle tough grass and uneven terrain without straining. Equipped with a hydrostatic transmission, this mower provides seamless speed control and a responsive driving experience. Operators can easily adjust their speed without hassle, which is particularly beneficial for navigating around obstacles in the yard.

One of the exceptional features of the Poulan PD25PH48STE is its 48-inch cutting deck. This wide cutting deck allows for increased productivity, as it enables users to cover more ground in less time. The deck is designed with three precision blades, promoting an even cut while reducing the likelihood of grass clumping. Furthermore, the cutting height can be easily adjusted, ranging from 1 to 4 inches, allowing users to customize their mowing experience according to their lawn conditions.

Another notable attribute of the PD25PH48STE is its comfortable and ergonomic seating. The high-back seat provides ample support, making long mowing sessions more enjoyable. Additionally, the design features a user-friendly dashboard, where operators can control the mower's various functions and monitor engine performance at a glance.

Safety is also a top priority with this model. The PD25PH48STE includes essential safety features such as an auto shut-off function that activates when the operator leaves the seat, protecting against accidental injuries. The robust frame is built to withstand the rigors of lawn care while ensuring stability and durability.

Moreover, the Poulan PD25PH48STE supports innovative technologies, including a maintenance-free battery and easy-access grease fittings for straightforward upkeep. This design focus guarantees the mower's longevity, allowing owners to invest in a product that will serve them well for years to come.

In summary, the Poulan PD25PH48STE is a reliable riding mower that combines power, versatility, and user-friendly features. Its robust engine, wide cutting deck, and safety-focused design make it an ideal choice for homeowners seeking to maintain their lawns efficiently. As a trusted name in outdoor equipment, Poulan continues to deliver quality products that enhance the mowing experience.
Top Page Image Contents