Poulan PD25PH48STE owner manual To Replace Mower Drive Belt

Page 22

SERVICE AND ADJUSTMENTS

TO REPLACE MOWER DRIVE BELT

MOWER DRIVE BELT REMOVAL (See Fig. 23)

Park tractor on a level surface. Engage parking brake.

Lower mower to its lowest position.

Disengage belt tention rod from lock bracket.

CAUTION: Rod is spring loaded. Have a tight grip on rod and release slowly.

Remove screws from R.H. mandrel cover and remove cover.

Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface.

Disconnect R.H.suspension arm from rear deck bracket by removing retainer spring.

Roll belt over the top of R.H. mandrel pulley carefully.

Remove belt from electric clutch pulley.

Remove belt from idler pulleys.

Check primary idler arm and two idlers to see that they rotate freely.

Be sure spring is securely hooked to primary idler arm and spring arm.

MOWER DRIVE BELT INSTALLATION (See Fig. 23)

Install belt in both idlers.

Install new belt onto electric clutch pulley.

Roll belt into upper groove of R.H. mandrel pulley care- fully.

Carefully check belt routing making sure belt is in the grooves correctly.

Reconnect R.H. suspension arm to rear deck bracket with retainer spring.

Reassemble R.H. mandrel cover.

Engage belt tension rod by pushing rod into locking bracket.

BELT

RH

 

TENSION ROD

 

SUSPENSION

RH MANDREL

(DISENGAGED

POSITION)

ARM

COVER

IDLER

 

 

PULLEY

ELECTRIC

 

 

CLUTCH

 

 

PULLEY

 

 

IDLER

 

 

PULLEY

SPRING

 

 

ARM

 

 

PRIMARY

 

 

IDLER ARM

R.H.

 

 

02513

 

MANDREL

 

 

FIG. 23

TO REPLACE MOWER BLADE (SECONDARY) DRIVE BELT (See Fig. 24)

Park the tractor on level surface. Engage parking brake.

Remove mower (See “TO REMOVE MOWER” in this section of manual).

Remove screws from R.H. and L.H. mandrel covers and remove covers.

REMOVE MOWER DRIVE BELT

(Refer to “TO REMOVE MOWER DRIVE BELT” illustration in this section of manual).

Carefully roll belt over the top of R.H. mandrel pulley.

Remove belt from idler pulleys.

Check primary idler arm and two idlers to see that they rotate freely.

Be sure spring is securely hooked to primary idler arm and spring arm.

REMOVE MOWER BLADE (SECONDARY) DRIVE BELT

Carefully roll belt off L.H. mandrel pulley.

Remove belt from center mandrel pulley, idler pulley, and R.H. mandrel pulley.

Remove any dirt or grass which may have accumulated around mandrels and entire upper deck surface.

Check secondary idler arm and idler pulley to see that they rotate freely.

Be sure spring is hooked in secondary idler arm and secondary spring arm.

INSTALL NEW MOWER BLADE (SECONDARY) DRIVE BELT

Install new belt in lower groove of R.H. mandrel pulley, idler pulley, and center mandrel pulley as shown.

Carefully roll belt over L.H. mandrel pulley. Make sure belt is in all grooves properly.

REINSTALL MOWER DRIVE BELT

(Refer to “TO REMOVE MOWER DRIVE BELT” illustration in this section of manual).

Install belt into upper groove of R.H. mandrel pulley and around both idlers. Pull belt to front of mower to remove slack.

Reinstall mandrel covers and securely tighten all screws.

Carefully check belt routing making sure belt is in all grooves correctly.

Reinstall mower to tractor (See “TO INSTALL MOWER” in this section of manual).

SECONDARY

L.H. MANDREL IDLER ARM

IDLER PULLEY

SPRING

SECONDARY SPRING ARM

CENTER

MANDREL

R.H.

 

MANDREL

 

COVER

02515

FIG. 24

22

Image 22
Contents PD25PH48STE Safety Rules Safety Rules Table of Contents Seat Nose Roller Unassembled PartsSteering Wheel Gauge Wheels MowerHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs To Attach Nose Roller See FigCheck for Proper Position of ALL Belts Check Tire PressureCheck Mower Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Transport See FigsCheck Engine OIL Level Before Starting the EngineTowing Carts and Other ATTACH- Ments ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP General Recommendations MaintenanceLubrication Chart Before Each USETractor Engine Cleaning To Install Mower Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Drive Belt To Replace Mower Blade Secondary Drive Belt See FigTransmission REMOVAL/REPLACEMENT To Check and Adjust Brake See FigTo Replace Motion Drive Belt See Fig Replacing Battery See Fig To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionWith attachment clutch Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Parts and Service For Service or Replacement Parts

PD25PH48STE specifications

The Poulan PD25PH48STE is a standout in the realm of lawn care, known for its power, efficiency, and user-friendly design. This riding mower is engineered for homeowners who seek a reliable and robust machine capable of handling larger lawns with ease and precision.

At the heart of the PD25PH48STE is a strong 25 horsepower Briggs & Stratton engine. This powerful engine ensures smooth operation and can tackle tough grass and uneven terrain without straining. Equipped with a hydrostatic transmission, this mower provides seamless speed control and a responsive driving experience. Operators can easily adjust their speed without hassle, which is particularly beneficial for navigating around obstacles in the yard.

One of the exceptional features of the Poulan PD25PH48STE is its 48-inch cutting deck. This wide cutting deck allows for increased productivity, as it enables users to cover more ground in less time. The deck is designed with three precision blades, promoting an even cut while reducing the likelihood of grass clumping. Furthermore, the cutting height can be easily adjusted, ranging from 1 to 4 inches, allowing users to customize their mowing experience according to their lawn conditions.

Another notable attribute of the PD25PH48STE is its comfortable and ergonomic seating. The high-back seat provides ample support, making long mowing sessions more enjoyable. Additionally, the design features a user-friendly dashboard, where operators can control the mower's various functions and monitor engine performance at a glance.

Safety is also a top priority with this model. The PD25PH48STE includes essential safety features such as an auto shut-off function that activates when the operator leaves the seat, protecting against accidental injuries. The robust frame is built to withstand the rigors of lawn care while ensuring stability and durability.

Moreover, the Poulan PD25PH48STE supports innovative technologies, including a maintenance-free battery and easy-access grease fittings for straightforward upkeep. This design focus guarantees the mower's longevity, allowing owners to invest in a product that will serve them well for years to come.

In summary, the Poulan PD25PH48STE is a reliable riding mower that combines power, versatility, and user-friendly features. Its robust engine, wide cutting deck, and safety-focused design make it an ideal choice for homeowners seeking to maintain their lawns efficiently. As a trusted name in outdoor equipment, Poulan continues to deliver quality products that enhance the mowing experience.