Poulan PD25PH48STE owner manual Storage, Other, Fuel System, Engine OIL, Cylinders

Page 26

STORAGE

Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more.

WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

•Clean entire tractor (See “CLEANING” in the Mainte- nance section of this manual).

•Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

•Lubricate as shown in the Maintenance section of this manual.

•Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

•Touch up all rusted or chipped paint surfaces; sand lightly before painting.

BATTERY

•Fully charge the battery for storage.

•After a period of time in storage, battery may require recharging.

•To help prevent corrosion and power leakage during long periods of storage, battery cables should be dis- connected and battery cleaned thoroughly (see “TO CLEAN BATTERY AND TERMINALS” in the Mainte- nance section of this manual).

•After cleaning, leave cables disconnected and place cables where they cannot come in contact with battery terminals.

•If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANTTO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTUREWHICH LEADSTO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

•Empty the fuel tank by starting the engine and let it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in mini- mizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER(S)

•Remove spark plug(s).

•Pour one ounce of oil through spark plug hole(s) into cylinder(s).

•Turn ignition key to “START” position for a few seconds to distribute oil.

•Replace with new spark plug(s).

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your tractor indoors and cover it to give protection from dust and dirt.

•Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust.

IMPORTANT: NEVER COVERTRACTOR WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents PD25PH48STE Safety Rules Safety Rules Table of Contents Seat Nose Roller Unassembled PartsSteering Wheel Gauge Wheels MowerHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs To Attach Nose Roller See FigCheck for Proper Position of ALL Belts Check Tire PressureCheck Mower Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Transport See FigsCheck Engine OIL Level Before Starting the EngineTowing Carts and Other ATTACH- Ments ADD GasolineAutomatic Transmission Warm UP Purge TransmissionMowing Tips General Recommendations MaintenanceLubrication Chart Before Each USETractor Engine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Drive Belt To Replace Mower Blade Secondary Drive Belt See FigTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTransmission REMOVAL/REPLACEMENT Replacing Battery See Fig To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionWith attachment clutch Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Parts and Service For Service or Replacement Parts

PD25PH48STE specifications

The Poulan PD25PH48STE is a standout in the realm of lawn care, known for its power, efficiency, and user-friendly design. This riding mower is engineered for homeowners who seek a reliable and robust machine capable of handling larger lawns with ease and precision.

At the heart of the PD25PH48STE is a strong 25 horsepower Briggs & Stratton engine. This powerful engine ensures smooth operation and can tackle tough grass and uneven terrain without straining. Equipped with a hydrostatic transmission, this mower provides seamless speed control and a responsive driving experience. Operators can easily adjust their speed without hassle, which is particularly beneficial for navigating around obstacles in the yard.

One of the exceptional features of the Poulan PD25PH48STE is its 48-inch cutting deck. This wide cutting deck allows for increased productivity, as it enables users to cover more ground in less time. The deck is designed with three precision blades, promoting an even cut while reducing the likelihood of grass clumping. Furthermore, the cutting height can be easily adjusted, ranging from 1 to 4 inches, allowing users to customize their mowing experience according to their lawn conditions.

Another notable attribute of the PD25PH48STE is its comfortable and ergonomic seating. The high-back seat provides ample support, making long mowing sessions more enjoyable. Additionally, the design features a user-friendly dashboard, where operators can control the mower's various functions and monitor engine performance at a glance.

Safety is also a top priority with this model. The PD25PH48STE includes essential safety features such as an auto shut-off function that activates when the operator leaves the seat, protecting against accidental injuries. The robust frame is built to withstand the rigors of lawn care while ensuring stability and durability.

Moreover, the Poulan PD25PH48STE supports innovative technologies, including a maintenance-free battery and easy-access grease fittings for straightforward upkeep. This design focus guarantees the mower's longevity, allowing owners to invest in a product that will serve them well for years to come.

In summary, the Poulan PD25PH48STE is a reliable riding mower that combines power, versatility, and user-friendly features. Its robust engine, wide cutting deck, and safety-focused design make it an ideal choice for homeowners seeking to maintain their lawns efficiently. As a trusted name in outdoor equipment, Poulan continues to deliver quality products that enhance the mowing experience.
Top Page Image Contents