Poulan PO14542C manual Before Starting the Engine, To Operate on Hills, To Transport

Page 12

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 6)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole with shoulder bolt, 17/32 washer, 3/8 washer, and 3/8-16 locknut and tighten securely.

•Repeat for opposite side installing gauge wheel in same adjustment hole.

GAUGE

WHEEL

MOUNTING

BRACKET

3/8-16

LOCKNUT

17/32 WASHER

3/8 WASHER

 

SHOULDER

GAUGE WHEEL

BOLT

FIG. 6

TO OPERATE MOWER (See Fig. 7)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

"ENGAGED" POSITION

ATTACHMENT LIFT

LEVER HIGH POSITION

LOW

POSITION

ATTACHMENT

DEFLECTOR

CLUTCH LEVER

"DISENGAGED"

SHIELD

POSITION

FIG. 7

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

TO OPERATE ON HILLS

CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move gearshift lever to 1st gear. Be sure you have allowed room for tractor to roll slightly as you restart movement.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Make all turns slowly.

TO TRANSPORT

•Raise attachment lift to highest position with attachment lift control.

•When pushing or towing your tractor, be sure gearshift lever is in neutral (N) position.

•Do not push or tow tractor at more than five (5) MPH.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

TOWING CARTS AND OTHER ATTACH- MENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

•The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

•Check engine oil with tractor on level ground.

•Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Customer Responsibilities section of this manual).

•To change engine oil, see the Customer Responsibilities

12section in this manual.

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Model NO. PO14542C Safety Rules IV. ServiceGeneral Operation II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesUnassembled Parts Steering Wheel SeatKeys Slope SheetAssembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidHOW to SET UP Your Tractor Check Battery See FigInstall Seat See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Operate on HillsTo Transport Towing Carts and Other ATTACH- MentsMowing Tips ADD GasolineTo Start Engine See Fig Lubrication Chart Customer ResponsibilitiesGeneral Recommendations Before Each USETractor Brake OperationTires Operator Presence SystemBattery EngineBelts Transaxle CoolingClean AIR Screen To Service PRE-CLEANERTo Service Cartridge Engine Cooling Fins See FigCleaning MufflerSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERReplacing Battery See Figs To Remove Hood and Grill Assembly See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable See Fig To Adjust CarburetorStorage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PO14542CElectrical KEY Part NO. NO. Description Chassis and Enclosures KEY Part Description Drive Transaxle Peerless Model 206-545C Steering Assembly Repair Parts Engine KEY Part Description Seat Assembly Decals Wheels & TiresMower Lift Nut Lock w/Wsh 1/2-13 Unc Mower Deck Washer, Spacer Mower Vented Service Notes Limited Warranty Policy ForSuggested Guide for Sighting Slopes for Safe Operation

PO14542C specifications

The Poulan PO14542C is a standout choice for homeowners and lawn care enthusiasts looking for a powerful and efficient riding lawn mower. This machine boasts an array of features and technologies designed to enhance performance, comfort, and ease of use, making it a reliable tool for maintaining your lawn.

At the core of the Poulan PO14542C is its robust engine. Equipped with a 14.5 horsepower Briggs & Stratton engine, this mower delivers sufficient power for mowing large areas quickly and efficiently. The engine is designed for easy starting and smooth operation, ensuring that users can tackle their lawn care tasks without hassle.

One of the key features of the PO14542C is its 42-inch cutting deck. This wide cutting swath allows users to cover more ground in less time, making lawn maintenance a quicker process. The cutting deck is adjustable, with several height settings, enabling users to achieve their desired grass length while accommodating varying lawn types and conditions.

The mower also incorporates a Hydrostatic transmission system, which provides seamless speed control and eliminates the need for shifting gears. This feature is particularly beneficial for users who want to maneuver around obstacles or adjust their speed without interruption.

Comfort is another significant consideration in the design of the PO14542C. It features a high-back seat with ample cushioning, allowing for a more comfortable ride during extended mowing sessions. The ergonomic design of the controls ensures that every function is within easy reach, providing a user-friendly experience for individuals of all sizes.

In terms of durability, the Poulan PO14542C is built to last. The frame and body are constructed from high-quality materials that can withstand the rigors of regular use. Additionally, the mower’s reinforced cutting deck ensures that it can handle tough mowing conditions without compromising performance.

For those who prioritize efficiency and versatility, this riding mower is compatible with a variety of attachments, enabling users to switch out the mowing deck for baggers, mulchers, and other implements. This versatility adds to the overall utility of the machine, making it a valuable asset in any lawn care toolkit.

Overall, the Poulan PO14542C is an exceptional riding lawn mower that caters to the needs of users seeking efficiency, comfort, and reliability in their lawn maintenance tasks. With its powerful engine, adjustable cutting deck, and advanced transmission systems, it stands out in the crowded market of lawn care equipment.
Top Page Image Contents