Poulan PO14542C To Level Mower Housing, To Replace Mower Blade Drive Belt See Fig, Belt Removal

Page 20

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 17 and 18)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

BOTTOM EDGE

OF MOWER

OF MOWER

TO GROUND

TO GROUND

“A”

“A”

 

GROUND LINE

FIG. 17

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

"D"

"D"

FIG. 19

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT "F"

NUT "E"

TRUNNION

FRONT LINKS

SUSPENSION ARM

LIFT LINK

ADJUSTMENT

NUT

FIG. 18

FRONT-TO-BACK ADJUSTMENT (See Figs. 19 and 20)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO- SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

• Before making any necessary adjustments, check that both front links are equal in length.

• If links are not equal in length, adjust one link to same length as other link.

• To lower front of mower loosen nut “E” on both front links

FIG. 20

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 21)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instructions.

MANDREL

IDLER

PULLEY

PULLEYS

 

MANDREL

PULLEY

an equal number of turns.

20

FIG. 21

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Model NO. PO14542C Safety Rules IV. ServiceGeneral Operation II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesUnassembled Parts Steering Wheel SeatKeys Slope SheetAssembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Operate on HillsTo Transport Towing Carts and Other ATTACH- MentsTo Start Engine See Fig Mowing TipsADD Gasoline Lubrication Chart Customer ResponsibilitiesGeneral Recommendations Before Each USETractor Brake OperationTires Operator Presence SystemBattery EngineBelts Transaxle CoolingClean AIR Screen To Service PRE-CLEANERTo Service Cartridge Engine Cooling Fins See FigCleaning MufflerSpark Plugs IN-LINE Fuel Filter See FigTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERReplacing Battery See Figs To Remove Hood and Grill Assembly See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable See Fig To Adjust CarburetorStorage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PO14542CElectrical KEY Part NO. NO. Description Chassis and Enclosures KEY Part Description Drive Transaxle Peerless Model 206-545C Steering Assembly Repair Parts Engine KEY Part Description Seat Assembly Decals Wheels & TiresMower Lift Nut Lock w/Wsh 1/2-13 Unc Mower Deck Washer, Spacer Mower Vented Service Notes Limited Warranty Policy ForSuggested Guide for Sighting Slopes for Safe Operation

PO14542C specifications

The Poulan PO14542C is a standout choice for homeowners and lawn care enthusiasts looking for a powerful and efficient riding lawn mower. This machine boasts an array of features and technologies designed to enhance performance, comfort, and ease of use, making it a reliable tool for maintaining your lawn.

At the core of the Poulan PO14542C is its robust engine. Equipped with a 14.5 horsepower Briggs & Stratton engine, this mower delivers sufficient power for mowing large areas quickly and efficiently. The engine is designed for easy starting and smooth operation, ensuring that users can tackle their lawn care tasks without hassle.

One of the key features of the PO14542C is its 42-inch cutting deck. This wide cutting swath allows users to cover more ground in less time, making lawn maintenance a quicker process. The cutting deck is adjustable, with several height settings, enabling users to achieve their desired grass length while accommodating varying lawn types and conditions.

The mower also incorporates a Hydrostatic transmission system, which provides seamless speed control and eliminates the need for shifting gears. This feature is particularly beneficial for users who want to maneuver around obstacles or adjust their speed without interruption.

Comfort is another significant consideration in the design of the PO14542C. It features a high-back seat with ample cushioning, allowing for a more comfortable ride during extended mowing sessions. The ergonomic design of the controls ensures that every function is within easy reach, providing a user-friendly experience for individuals of all sizes.

In terms of durability, the Poulan PO14542C is built to last. The frame and body are constructed from high-quality materials that can withstand the rigors of regular use. Additionally, the mower’s reinforced cutting deck ensures that it can handle tough mowing conditions without compromising performance.

For those who prioritize efficiency and versatility, this riding mower is compatible with a variety of attachments, enabling users to switch out the mowing deck for baggers, mulchers, and other implements. This versatility adds to the overall utility of the machine, making it a valuable asset in any lawn care toolkit.

Overall, the Poulan PO14542C is an exceptional riding lawn mower that caters to the needs of users seeking efficiency, comfort, and reliability in their lawn maintenance tasks. With its powerful engine, adjustable cutting deck, and advanced transmission systems, it stands out in the crowded market of lawn care equipment.
Top Page Image Contents