Poulan PO14542C manual To Adjust Steering Wheel Alignment, Front Wheel TOE-IN/CAMBER

Page 21

SERVICE AND ADJUSTMENTS

TO ADJUST BRAKE (See Fig. 22)

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than six (6) feet stopping distance at high speed in highest gear on a level dry concrete or paved surface, then brake must be adjusted.

•Depress clutch/brake pedal and engage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

•If distance is other than 1-1/2", loosen jam nut and turn nut “A” until distance becomes 1-1/2". Retighten jam nut against nut “A”.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than six (6) feet in highest gear, further maintenance is necessary. Contact your nearest au- thorized service center/department.

WITH PARKING BRAKE "ENGAGED"

1-1/2"

NUT "A"

JAM NUT

OPERATING

ARM

FIG. 22

TO REPLACE MOTION DRIVE BELT (See Fig. 23)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

•Remove mower (See “TO REMOVE MOWER” in this section of this manual.)

•Remove belt from stationary idler and clutching idler.

•Pull belt slack toward rear of tractor. Remove belt upwards from transaxle pulley by deflecting belt keep- ers.

•Pull belt toward front of tractor and remove downwards from around engine pulley.

•Install new belt by reversing above procedure.

ENGINE

PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

TRANSAXLE

PULLEY

FIG. 23

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe- in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 24)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

 

WHEEL ONLY)

FIG. 24

TO START ENGINE WITH A WEAK BATTERY (See Fig. 25)

CAUTION: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Customer Responsibili- ties section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT NEGATIVE GROUNDED SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT NEGATIVE GROUNDED SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect each end of the RED cable to the POSITIVE (+)

terminal of each battery, taking care not to short against

21chassis.

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model NO. PO14542C IV. Service Safety RulesGeneral Operation II. Slope OperationTable of Contents Customer Responsibilities Product SpecificationsSteering Wheel Seat Unassembled PartsKeys Slope SheetTools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidHOW to SET UP Your Tractor Check Battery See FigInstall Seat See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Before Starting the EngineTo Transport Towing Carts and Other ATTACH- MentsMowing Tips ADD GasolineTo Start Engine See Fig Customer Responsibilities Lubrication ChartGeneral Recommendations Before Each USEBrake Operation TractorTires Operator Presence SystemEngine BatteryBelts Transaxle CoolingTo Service PRE-CLEANER Clean AIR ScreenTo Service Cartridge Engine Cooling Fins See FigMuffler CleaningSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig Belt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentTo Remove Hood and Grill Assembly See Fig Replacing Battery See FigsTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor To Adjust Throttle Control Cable See FigOther StorageFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number PO14542C SchematicElectrical KEY Part NO. NO. Description Chassis and Enclosures KEY Part Description Drive Transaxle Peerless Model 206-545C Steering Assembly Repair Parts Engine KEY Part Description Seat Assembly Wheels & Tires DecalsMower Lift Nut Lock w/Wsh 1/2-13 Unc Mower Deck Washer, Spacer Mower Vented Service Notes Limited Warranty For PolicySuggested Guide for Sighting Slopes for Safe Operation

PO14542C specifications

The Poulan PO14542C is a standout choice for homeowners and lawn care enthusiasts looking for a powerful and efficient riding lawn mower. This machine boasts an array of features and technologies designed to enhance performance, comfort, and ease of use, making it a reliable tool for maintaining your lawn.

At the core of the Poulan PO14542C is its robust engine. Equipped with a 14.5 horsepower Briggs & Stratton engine, this mower delivers sufficient power for mowing large areas quickly and efficiently. The engine is designed for easy starting and smooth operation, ensuring that users can tackle their lawn care tasks without hassle.

One of the key features of the PO14542C is its 42-inch cutting deck. This wide cutting swath allows users to cover more ground in less time, making lawn maintenance a quicker process. The cutting deck is adjustable, with several height settings, enabling users to achieve their desired grass length while accommodating varying lawn types and conditions.

The mower also incorporates a Hydrostatic transmission system, which provides seamless speed control and eliminates the need for shifting gears. This feature is particularly beneficial for users who want to maneuver around obstacles or adjust their speed without interruption.

Comfort is another significant consideration in the design of the PO14542C. It features a high-back seat with ample cushioning, allowing for a more comfortable ride during extended mowing sessions. The ergonomic design of the controls ensures that every function is within easy reach, providing a user-friendly experience for individuals of all sizes.

In terms of durability, the Poulan PO14542C is built to last. The frame and body are constructed from high-quality materials that can withstand the rigors of regular use. Additionally, the mower’s reinforced cutting deck ensures that it can handle tough mowing conditions without compromising performance.

For those who prioritize efficiency and versatility, this riding mower is compatible with a variety of attachments, enabling users to switch out the mowing deck for baggers, mulchers, and other implements. This versatility adds to the overall utility of the machine, making it a valuable asset in any lawn care toolkit.

Overall, the Poulan PO14542C is an exceptional riding lawn mower that caters to the needs of users seeking efficiency, comfort, and reliability in their lawn maintenance tasks. With its powerful engine, adjustable cutting deck, and advanced transmission systems, it stands out in the crowded market of lawn care equipment.
Top Page Image Contents