Poulan PD25PH48STD To Check and Adjust Brake See Fig, To Replace Motion Drive Belt See Fig

Page 23

SERVICE AND ADJUSTMENTS

TO CHECK AND ADJUST BRAKE (See Fig. 25)

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.

TO CHECK BRAKE

•Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

•Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE

•Depress brake pedal all the way down and engage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

•If distance is other than 1-3/4", loosen jam nut and turn nut “A” until distance becomes 1-3/4". Retighten jam nut against nut “A”.

•Engage transmission by placing freewheel control in “transmission engaged” position.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is necessary. Replace brake pads or contact a qualified service center.

WITH PARKING BRAKE “ENGAGED”

1-3/4"

NUT “A”

JAM NUT

OPERATING

ARM

02537

DO NOT TOUCH THIS NUT. IF FURTHER BRAKE ADJUSTMENT IS NECESSARY CONTACT YOUR NEAREST AUTHORIZED SER- VICE CENTER/DEPARTMENT

FIG. 25

TO REPLACE MOTION DRIVE BELT (See Fig. 26)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Disconnect clutch wire harness.

•Remove clutch locator.

•Remove belt from stationary idler and clutching idler.

•Remove belt downward from engine pulley and around electric clutch.

•Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades.

•Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

•Carefully work new belt down around transmission cooling fan and onto the input pulley.

•Slide belt into the center span keeper.

•Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley.

•Install belt through stationary idler and clutching idler.

•Reinstall clutch locator and tighten nut securely.

•Reconnect clutch harness.

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

ELECTRIC

CLUTCH LOCATOR

CLUTCH

 

CLUTCHING

IDLER

STATIONARY

IDLER

CENTER SPAN

KEEPER

TRANSMISSION

CLUTCH

INPUT PULLEY

WIRE

 

HARNESS

FIG. 26

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See“PURGETRANSMISSION” in the Operation section of this manual.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents PD25PH48STD Safety Rules Safety Rules Table of Contents Mower Unassembled PartsSteering Wheel Gauge Wheels Seat Nose RollerTo Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See FigsCheck Brake System Check Tire PressureCheck Mower Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelAutomatic Transmission Warm UP Purge TransmissionMowing Tips Before Each USE MaintenanceLubrication Chart General RecommendationsTractor Engine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Secondary Drive Belt See Fig To Replace Mower Drive BeltTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTransmission REMOVAL/REPLACEMENT Front Wheel TOE-IN/CAMBER To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Replacing Battery See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsWith attachment clutch Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation For Service or Replacement Parts Parts and Service

PD25PH48STD specifications

The Poulan PD25PH48STD is a lawn tractor designed to offer homeowners an efficient and reliable mowing experience. With its robust engine and user-friendly features, this model ensures a seamless lawn maintenance process that meets the needs of various yard sizes.

One of the standout features of the PD25PH48STD is its powerful 25 HP Briggs & Stratton engine. This engine provides ample power to tackle tough grass and uneven terrain, ensuring a consistent cut with every pass. Coupled with an automatic transmission, the tractor offers smooth operation and effortless speed control, allowing users to choose the right pace for their mowing tasks.

The PD25PH48STD sports a 48-inch cutting deck, which enables it to cover more ground in less time. This deck is equipped with reinforced blades designed for optimum cutting efficiency, delivering a clean and even finish. The adjustable cutting height feature allows users to customize the grass length, adapting to various landscaping needs or seasonal changes.

Another important aspect of the Poulan PD25PH48STD is its ergonomic design. The operator's seat is comfortable and adjustable, ensuring that users can find their ideal driving position for long mowing sessions. The easy-to-reach controls enhance user experience, allowing for intuitive operation without the need to stretch or fumble.

In terms of durability, the PD25PH48STD is constructed with high-quality materials that are designed to withstand the rigors of outdoor use. The sturdy frame and robust components ensure that the tractor can handle tough tasks year after year. Moreover, the tractor’s maintenance-friendly design simplifies routine checks and repairs, ensuring that it stays in peak condition with minimal effort.

The Poulan PD25PH48STD also embraces modern technology with features like a large fuel tank that extends mowing time between refuels and easy-to-read gauges that provide vital information at a glance.

In summary, the Poulan PD25PH48STD lawn tractor combines power, efficiency, and user-friendly features to create a reliable mowing solution for homeowners. With its strong engine, spacious cutting deck, and ergonomic design, it not only makes lawn care easier but also enhances the overall mowing experience, making it a worthy investment for any yard maintenance enthusiast.
Top Page Image Contents