Poulan PD25PH48STD owner manual To Adjust Steering Wheel ALIGN- Ment, Front Wheel TOE-IN/CAMBER

Page 24

SERVICE AND ADJUSTMENTS

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 27)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE

COVER

00663

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 27

TO START ENGINE WITH A WEAK BATTERY (See Fig. 28)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

02614

WEAK OR DEAD

FULLY CHARGED

BATTERY

BATTERY

FIG. 28

REPLACING BATTERY (See Fig. 29)

CAUTION: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands,rings,etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

•Lift hood to raised position.

•Remove terminal guard.

•Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•Reinstall terminal guard.

•First connect RED battery cable to positive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely.

•Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and keps nut. Tighten securely

•Close terminal access doors.

•Close hood.

when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START

KEPS NUT

TERMINAL

ACCESS

DOOR

TERMINAL

02179

GUARD

 

HEX

BOLT

POSITIVE (RED)

CABLE

NEGATIVE (BLACK)

CABLE

OTHER VEHICLES.

FIG. 29

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents PD25PH48STD Safety Rules Safety Rules Table of Contents Unassembled Parts Steering Wheel Gauge WheelsSeat Nose Roller MowerAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs To Attach Nose Roller See FigCheck Tire Pressure Check Mower LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Engine Cleaning Service and Adjustments To Install MowerTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Drive Belt To Replace Mower Blade Secondary Drive Belt See FigTo Check and Adjust Brake See Fig Transmission REMOVAL/REPLACEMENTTo Replace Motion Drive Belt See Fig To Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigReplacing Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionWith attachment clutch Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Parts and Service For Service or Replacement Parts

PD25PH48STD specifications

The Poulan PD25PH48STD is a lawn tractor designed to offer homeowners an efficient and reliable mowing experience. With its robust engine and user-friendly features, this model ensures a seamless lawn maintenance process that meets the needs of various yard sizes.

One of the standout features of the PD25PH48STD is its powerful 25 HP Briggs & Stratton engine. This engine provides ample power to tackle tough grass and uneven terrain, ensuring a consistent cut with every pass. Coupled with an automatic transmission, the tractor offers smooth operation and effortless speed control, allowing users to choose the right pace for their mowing tasks.

The PD25PH48STD sports a 48-inch cutting deck, which enables it to cover more ground in less time. This deck is equipped with reinforced blades designed for optimum cutting efficiency, delivering a clean and even finish. The adjustable cutting height feature allows users to customize the grass length, adapting to various landscaping needs or seasonal changes.

Another important aspect of the Poulan PD25PH48STD is its ergonomic design. The operator's seat is comfortable and adjustable, ensuring that users can find their ideal driving position for long mowing sessions. The easy-to-reach controls enhance user experience, allowing for intuitive operation without the need to stretch or fumble.

In terms of durability, the PD25PH48STD is constructed with high-quality materials that are designed to withstand the rigors of outdoor use. The sturdy frame and robust components ensure that the tractor can handle tough tasks year after year. Moreover, the tractor’s maintenance-friendly design simplifies routine checks and repairs, ensuring that it stays in peak condition with minimal effort.

The Poulan PD25PH48STD also embraces modern technology with features like a large fuel tank that extends mowing time between refuels and easy-to-read gauges that provide vital information at a glance.

In summary, the Poulan PD25PH48STD lawn tractor combines power, efficiency, and user-friendly features to create a reliable mowing solution for homeowners. With its strong engine, spacious cutting deck, and ergonomic design, it not only makes lawn care easier but also enhances the overall mowing experience, making it a worthy investment for any yard maintenance enthusiast.
Top Page Image Contents