Poulan PD25PH48STD owner manual Install Seat See Fig, Assemble Gauge Wheels to Mower Deck See Fig

Page 7

ASSEMBLY

INSTALL SEAT (See Fig. 3)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

SEAT

SEAT PAN

SHOULDER

BOLT

FLAT WASHER

 

ADJUSTMENT

 

KNOB

02464

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing brake pedal.

•Place freewheel control in "transmission disengaged position" (See “TO TRANSPORT” in the Operation section of this manual).

•Roll tractor forward off skid.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been com- pleted.

•Check engine oil level and fill fuel tank with gasoline.

•Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual).

•Sit on seat in operating position, depress brake pedal and set the parking brake.

•Place motion control lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Start the engine.After engine has started, move throttle control to idle position.

•Release parking brake.

•Slowly move the motion control lever forward and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

•Turn ignition key to "STOP" position.

Continue with the instructions that follow.

ASSEMBLE GAUGE WHEELS TO MOWER DECK (See Fig. 4)

The gauge wheels are designed to keep the mower deck in properpositionwhenoperatingmower.Besuretheyareproperly adjusted to ensure optimum mower performance.

•Slide gauge wheel bar down into bracket channel, Be sure that gauge wheel bar aligning holes are on top. Assemble gauge wheels as shown using shoulder bolts, 3/8 washers and 3/8-16 center locknuts and tighten securely.

•For ease of mower to tractor assembly, raise gauge wheels to highest position and retain with clevis pins and spring retainers.

•Adjust gauge wheels before operating mower. See “TO ADJUST GAUGE WHEELS” in the Operation section of this manual.

RETAINER SPRING

PIN

ADJUSTING

SHOULDER BAR

BOLT

GAUGE

WHEEL 3/8-16 CENTER LOCKNUT

3/8 WASHER

FIG. 4

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents PD25PH48STD Safety Rules Safety Rules Table of Contents Mower Unassembled PartsSteering Wheel Gauge Wheels Seat Nose RollerTo Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See FigsCheck Brake System Check Tire PressureCheck Mower Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelMowing Tips Purge TransmissionAutomatic Transmission Warm UP Before Each USE MaintenanceLubrication Chart General RecommendationsTractor Engine Cleaning To Install Mower Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Secondary Drive Belt See Fig To Replace Mower Drive BeltTransmission REMOVAL/REPLACEMENT To Check and Adjust Brake See FigTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBER To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Replacing Battery See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsWith attachment clutch Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation For Service or Replacement Parts Parts and Service

PD25PH48STD specifications

The Poulan PD25PH48STD is a lawn tractor designed to offer homeowners an efficient and reliable mowing experience. With its robust engine and user-friendly features, this model ensures a seamless lawn maintenance process that meets the needs of various yard sizes.

One of the standout features of the PD25PH48STD is its powerful 25 HP Briggs & Stratton engine. This engine provides ample power to tackle tough grass and uneven terrain, ensuring a consistent cut with every pass. Coupled with an automatic transmission, the tractor offers smooth operation and effortless speed control, allowing users to choose the right pace for their mowing tasks.

The PD25PH48STD sports a 48-inch cutting deck, which enables it to cover more ground in less time. This deck is equipped with reinforced blades designed for optimum cutting efficiency, delivering a clean and even finish. The adjustable cutting height feature allows users to customize the grass length, adapting to various landscaping needs or seasonal changes.

Another important aspect of the Poulan PD25PH48STD is its ergonomic design. The operator's seat is comfortable and adjustable, ensuring that users can find their ideal driving position for long mowing sessions. The easy-to-reach controls enhance user experience, allowing for intuitive operation without the need to stretch or fumble.

In terms of durability, the PD25PH48STD is constructed with high-quality materials that are designed to withstand the rigors of outdoor use. The sturdy frame and robust components ensure that the tractor can handle tough tasks year after year. Moreover, the tractor’s maintenance-friendly design simplifies routine checks and repairs, ensuring that it stays in peak condition with minimal effort.

The Poulan PD25PH48STD also embraces modern technology with features like a large fuel tank that extends mowing time between refuels and easy-to-read gauges that provide vital information at a glance.

In summary, the Poulan PD25PH48STD lawn tractor combines power, efficiency, and user-friendly features to create a reliable mowing solution for homeowners. With its strong engine, spacious cutting deck, and ergonomic design, it not only makes lawn care easier but also enhances the overall mowing experience, making it a worthy investment for any yard maintenance enthusiast.
Top Page Image Contents