Poulan PK20H48YT manual To Attach Nose Roller See Fig, Assemble Gauge Wheels to Mower Deck See Fig

Page 8

ASSEMBLY

TO ATTACH NOSE ROLLER (See Fig. 4)

•Assemble brackets "A" and "B" to the inside of mower mounting brackets as shown. Tighten securely.

NOTE: Be sure bracket tabs are positioned in tab holes in mower brackets.

•Position nose roller between brackets and install rod and retainer spring.

LOCK

HEX

 

BOLT

ROD

NUT

 

 

TAB

"B"

BRACKET

HOLE

 

"A"

NOSE

BRACKET

02612

ROLLER

 

RETAINER SPRING

 

FIG. 4

ASSEMBLE GAUGE WHEELS TO MOWER DECK (See Fig. 5)

The gauge wheels are designed to keep the mower deck in proper position when operating mower. Be sure they are properly adjusted to ensure optimum mower perfor-

mance.

•Slide gauge wheel bar down into bracket channel, Be sure that gauge wheel bar aligning holes are on top. Assemble gauge wheels as shown using shoulder bolts, 3/8 washers and 3/8-16 center locknuts and tighten securely.

•For ease of mower to tractor assembly, raise gauge wheels to highest position and retain with clevis pins and spring retainers.

•Adjust gauge wheels before operating mower. See “TO ADJUST GAUGE WHEELS” in the Operation section of this manual.

RETAINER SPRING

PIN

SHOULDER

BOLT ADJUSTING

BAR

GAUGE

WHEEL3/8-16 CENTER

LOCKNUT

3/8 WASHER

FIG. 5

INSTALL MOWER AND DRIVE BELT (See Figs. 6 and 7)

Be sure tractor is on level surface and mower suspension arms are raised with attachment lift control. Engage park- ing brake.

•Cut and remove ties securing anti-sway bar and belts. Swing anti-sway bar to left side of mower deck.

•Slide mower under tractor with deflector shield to right side of tractor.

IMPORTANT: Check belt for proper routing in all mower pulley grooves.

•If equipped, turn height adjustment knob counter- clockwise until it stops.

•Lower mower linkage with attachment lift control.

•Be sure belt tension rod is in disengaged position.

•Install belt into electric clutch pulley groove.

•Place the suspension arms on outward pointing deck pins. Retain with double loop retainer spring with loops up as shown.

•Install front plate assembly to tractor suspension brackets and retain with single loop retainer springs as shown.

•Position front plate assembly between front mower brackets. Raise deck and plate assembly to align holes and insert flanged pins. Secure pins with double loop retainer springs between the plate assembly and mower brackets.

NOTE: To assist in locating hole in flanged pin, the hole in pin is inline with notch on head of pin.If necessary, move mower side-to-side to give space between plate and mower brackets.

IMPORTANT: Check belt for proper routing in all mower pulley grooves. Engage belt tension rod by pushing rod into locking bracket.

•Engage belt tension rod by pushing rod into locking bracket.

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly.

•Connect anti-sway bar to chassis bracket under left footrest and retain with double loop retainer spring.

•If equipped, turn height adjustment knob clockwise to remove slack from mower suspension.

•Raise deck to highest position.

•Adjust gauge wheels before operating mower as shown in the Operation section of this manual.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents PK20H48YT Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationIV. Towing ServiceIII. Children Table of Contents Unassembled Parts Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Assemble Gauge Wheels to Mower Deck See Fig Install Mower and Drive Belt See FigsTo Attach Nose Roller See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Operate Mower See FigReverse Operation System ROS Before Starting the Engine To Transport See FigsCheck Engine OIL Level ADD GasolineAutomatic Transmission Warm UP Mowing TipsPurge Transmission Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Blade Removal See FigTo Sharpen Blade See Fig Check Operator Presence SystemEngine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower To Level Mower Housing FRONT-TO-BACK Adjustment See FigsMower Drive Belt Installation To Replace Mower Drive BeltTo Check and Adjust Brake See Fig To Replace Mower Blade Secondary Drive Belt See FigTransaxle Motion Control Lever Neutral Adjustment See Fig Belt InstallationTo Replace Motion Drive Belt See Fig Belt RemovalTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER To Attach Jumper CablesTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace FuseStorage OtherFuel System Engine OILTroubleshooting Points Engine dies when Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PK20H48YT specifications

The Poulan PK20H48YT is a versatile and robust riding lawn mower, specifically designed to provide users with an efficient grass cutting experience. This model stands out for its combination of power, performance, and ease of use, making it an ideal choice for homeowners with medium to large lawns.

One of the main features of the Poulan PK20H48YT is its powerful 20 HP Kohler engine. This engine provides ample power for cutting through thick grass and tackling uneven terrain. Coupled with a reliable automatic transmission system, users can easily navigate their lawns without the hassle of shifting gears. The simplicity of operation ensures that both seasoned users and beginners can achieve professional-looking results with minimal effort.

The mower’s cutting deck, measuring 48 inches, allows for a wider path when mowing, reducing the number of passes required and significantly saving time. The deck is constructed from durable materials, designed to withstand the rigors of outdoor use while ensuring longevity. Additionally, the deck height can be easily adjusted, offering six different cutting positions ranging from 1.5 to 4 inches, allowing users to customize their lawn's appearance to personal preferences and grass types.

In terms of technology, the Poulan PK20H48YT features a comfortable and ergonomic operator's seat, enhancing user experience. With a built-in steering wheel and easy-to-reach controls, individuals can maneuver and operate the mower with ease. The model is also equipped with a rear bagger option, enabling grass clippings to be efficiently collected, reducing the need for additional clean-up after mowing.

Safety is a vital consideration in lawn care equipment, and the PK20H48YT does not disappoint. The mower comes with essential safety features such as blade brake and an operator presence system, ensuring the blades stop spinning when the operator leaves the seat.

Another important characteristic of the Poulan PK20H48YT is its durability and maintenance-friendly design. The mower’s robust construction, paired with easy-access maintenance points, simplifies regular upkeep, ensuring the equipment remains in prime working condition for years.

Overall, the Poulan PK20H48YT is a well-rounded riding lawn mower that offers power, efficiency, and user-friendliness, making it a top choice for homeowners seeking quality lawn care solutions. Whether tackling overgrown grass or maintaining a manicured lawn, this model is equipped to handle it all with ease.
Top Page Image Contents