Poulan PK20H48YT manual Transmission REMOVAL/REPLACEMENT, To Adjust Steering Wheel ALIGN- Ment

Page 25

SERVICE AND ADJUSTMENTS

MOTION CONTROL

NEUTRAL

LEVER

LOCK GATE

 

ADJUSTMENT

BOLT

FIG. 27

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See“PURGETRANSMISSION” in the Operation section of this manual.

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor.If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 28)

TO START ENGINE WITH A WEAK BATTERY (See Fig. 29)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

BLACK cable first from chassis and then from the fully charged battery.

RED cable last from both batteries.

Block up axle securely.

Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

Repair tire and reassemble.

On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

Replace washers and snap retaining ring securely in axle groove.

Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 28

FIG. 29

25

Image 25
Contents Always Wear EYE Protection During Operation PK20H48YTSafe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationIII. Children ServiceIV. Towing Table of Contents Unassembled Parts Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig To Attach Nose Roller See Fig Install Mower and Drive Belt See FigsAssemble Gauge Wheels to Mower Deck See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Operate Mower See FigTo Operate on Hills To Transport See Figs Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP Lubrication Chart MaintenanceGeneral Recommendations Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Check Operator Presence SystemEngine Cleaning To Install Mower Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Drive Belt Mower Drive Belt InstallationTo Replace Mower Blade Secondary Drive Belt See Fig To Check and Adjust Brake See FigBelt Installation Transaxle Motion Control Lever Neutral Adjustment See FigTo Replace Motion Drive Belt See Fig Belt RemovalTo Adjust Steering Wheel ALIGN- Ment Transmission REMOVAL/REPLACEMENTFront Wheel TOE-IN/CAMBER To Attach Jumper CablesTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace FuseOther StorageFuel System Engine OILTroubleshooting Points Engine dies when Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PK20H48YT specifications

The Poulan PK20H48YT is a versatile and robust riding lawn mower, specifically designed to provide users with an efficient grass cutting experience. This model stands out for its combination of power, performance, and ease of use, making it an ideal choice for homeowners with medium to large lawns.

One of the main features of the Poulan PK20H48YT is its powerful 20 HP Kohler engine. This engine provides ample power for cutting through thick grass and tackling uneven terrain. Coupled with a reliable automatic transmission system, users can easily navigate their lawns without the hassle of shifting gears. The simplicity of operation ensures that both seasoned users and beginners can achieve professional-looking results with minimal effort.

The mower’s cutting deck, measuring 48 inches, allows for a wider path when mowing, reducing the number of passes required and significantly saving time. The deck is constructed from durable materials, designed to withstand the rigors of outdoor use while ensuring longevity. Additionally, the deck height can be easily adjusted, offering six different cutting positions ranging from 1.5 to 4 inches, allowing users to customize their lawn's appearance to personal preferences and grass types.

In terms of technology, the Poulan PK20H48YT features a comfortable and ergonomic operator's seat, enhancing user experience. With a built-in steering wheel and easy-to-reach controls, individuals can maneuver and operate the mower with ease. The model is also equipped with a rear bagger option, enabling grass clippings to be efficiently collected, reducing the need for additional clean-up after mowing.

Safety is a vital consideration in lawn care equipment, and the PK20H48YT does not disappoint. The mower comes with essential safety features such as blade brake and an operator presence system, ensuring the blades stop spinning when the operator leaves the seat.

Another important characteristic of the Poulan PK20H48YT is its durability and maintenance-friendly design. The mower’s robust construction, paired with easy-access maintenance points, simplifies regular upkeep, ensuring the equipment remains in prime working condition for years.

Overall, the Poulan PK20H48YT is a well-rounded riding lawn mower that offers power, efficiency, and user-friendliness, making it a top choice for homeowners seeking quality lawn care solutions. Whether tackling overgrown grass or maintaining a manicured lawn, this model is equipped to handle it all with ease.