Poulan PK20H48YT manual To Replace Motion Drive Belt See Fig, Belt Removal, Belt Installation

Page 24

SERVICE AND ADJUSTMENTS

•If distance is other than 1-9/16", loosen jam nut and turn nut “A” until distance becomes 1-9/16". Retighten jam nut against nut “A”.

•Engage transmission by placing freewheel control in “transmission engaged” position.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is necessary. Replace brake pads or contact a qualified service center.

WITH PARKING BRAKE “ENGAGED”

NUT “A”

1-9/16”

JAM NUT

 

OPERATING

ARM

01513

DO NOT TOUCH THIS NUT. IF FURTHER BRAKE ADJUST- MENT IS NECESSARY CONTACT YOUR NEAREST AUTHO- RIZED SERVICE CENTER/DEPARTMENT

FIG. 25

TO REPLACE MOTION DRIVE BELT (See Fig. 26)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Disconnect clutch wire harness.

•Remove clutch locator.

•Remove belt from stationary idler and clutching idler.

•Remove belt downward from engine pulley and around electric clutch.

•Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades.

•Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

•Carefully work new belt down around transmission cooling fan and onto the input pulley.

•Slide belt into the center span keeper.

•Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley.

•Install belt through stationary idler and clutching idler.

•Reinstall clutch locator and tighten nut securely.

•Reconnect clutch harness.

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

ELECTRIC

CLUTCH LOCATOR

CLUTCH

 

CLUTCHING

IDLER

STATIONARY

IDLER

CENTER SPAN

KEEPER

TRANSMISSION

CLUTCH

INPUT PULLEY

WIRE

 

HARNESS

FIG. 26

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 27)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine off.

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (N) (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satis- fied.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents PK20H48YT Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Unassembled Parts Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Install Mower and Drive Belt See Figs To Attach Nose Roller See FigAssemble Gauge Wheels to Mower Deck See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Reverse Operation System ROSTo Operate on Hills Before Starting the Engine To Transport See FigsCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Blade Removal See FigTo Sharpen Blade See Fig Check Operator Presence SystemEngine Cleaning Service and Adjustments To Install MowerTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsMower Drive Belt Installation To Replace Mower Drive BeltTo Check and Adjust Brake See Fig To Replace Mower Blade Secondary Drive Belt See FigTransaxle Motion Control Lever Neutral Adjustment See Fig Belt InstallationTo Replace Motion Drive Belt See Fig Belt RemovalTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER To Attach Jumper CablesTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace FuseStorage OtherFuel System Engine OILTroubleshooting Points Engine dies when Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PK20H48YT specifications

The Poulan PK20H48YT is a versatile and robust riding lawn mower, specifically designed to provide users with an efficient grass cutting experience. This model stands out for its combination of power, performance, and ease of use, making it an ideal choice for homeowners with medium to large lawns.

One of the main features of the Poulan PK20H48YT is its powerful 20 HP Kohler engine. This engine provides ample power for cutting through thick grass and tackling uneven terrain. Coupled with a reliable automatic transmission system, users can easily navigate their lawns without the hassle of shifting gears. The simplicity of operation ensures that both seasoned users and beginners can achieve professional-looking results with minimal effort.

The mower’s cutting deck, measuring 48 inches, allows for a wider path when mowing, reducing the number of passes required and significantly saving time. The deck is constructed from durable materials, designed to withstand the rigors of outdoor use while ensuring longevity. Additionally, the deck height can be easily adjusted, offering six different cutting positions ranging from 1.5 to 4 inches, allowing users to customize their lawn's appearance to personal preferences and grass types.

In terms of technology, the Poulan PK20H48YT features a comfortable and ergonomic operator's seat, enhancing user experience. With a built-in steering wheel and easy-to-reach controls, individuals can maneuver and operate the mower with ease. The model is also equipped with a rear bagger option, enabling grass clippings to be efficiently collected, reducing the need for additional clean-up after mowing.

Safety is a vital consideration in lawn care equipment, and the PK20H48YT does not disappoint. The mower comes with essential safety features such as blade brake and an operator presence system, ensuring the blades stop spinning when the operator leaves the seat.

Another important characteristic of the Poulan PK20H48YT is its durability and maintenance-friendly design. The mower’s robust construction, paired with easy-access maintenance points, simplifies regular upkeep, ensuring the equipment remains in prime working condition for years.

Overall, the Poulan PK20H48YT is a well-rounded riding lawn mower that offers power, efficiency, and user-friendliness, making it a top choice for homeowners seeking quality lawn care solutions. Whether tackling overgrown grass or maintaining a manicured lawn, this model is equipped to handle it all with ease.
Top Page Image Contents