Poulan PD22PH48STA To Replace Mower Blade Drive Belt See Fig, Belt Removal, Belt Installation

Page 20

SERVICE AND ADJUSTMENTS

SIDE-TO-SIDE ADJUSTMENT (See Figs. 20 and 21)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER

 

OF MOWER

TO GROUND

 

TO GROUND

“A”

GROUND LINE

“A”

FIG. 20

SUSPENSION ARM

LIFT LINK ADJUSTMENT NUT

FIG. 21

FRONT-TO-BACK ADJUSTMENT (See Figs. 22 and 23)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO- SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length. Both links should be approximately 10-3/8".

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

• Recheck side-to-side adjustment.

20

MANDREL

"D"

"D"

FIG. 22

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT "E"

NUT "F"

TRUNNION

FRONT LINKS

FIG. 23

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 24)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instructions.

IDLER

PULLEYS

MANDREL

PULLEYS

FIG. 24

Page 19 Page 21
Image 20
Page 19 Page 21
Contents PR17H42STC Safety Rules Safe Operation Practices for Ride-On MowersBecome ALERT!!! Your Safety is IN- Volved Table of Contents Slope Sheet Unassembled PartsSteering Wheel Seat Assembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To SET UP Your Mower for Mulching Check Tire PressureCheck Deck Levelness To Convert to Bagging or DischargingOperation Know Your Tractor HOW to USE Your Tractor To Adjust Mower Cutting Height See Fig Stopping See FigTo SET Parking Brake See Fig To USE Throttle Control See FigTo Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsLubrication Chart Customer ResponsibilitiesGeneral Recommendations Before Each USETractor Engine Spark Plugs CleaningMuffler Service and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Adjust Brake See Fig Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral ADJUSTMENTSee Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment To Start Engine with a Weak Battery See FigReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Replace Fuse To Replace Headlight BulbInterlocks and Relays Storage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PR17H42STCElectrical 2122KEY Part Description Chassis 174619 Drive 175765 175578175461 175556Steering Assembly 175121 177876175146 175118Seat Assembly Decals Wheels and Tires178206 178219Engine Optional EquipmentSpark Arrester 8113170551 Control Th/ch Flag Mower Deck 143 159 144 150 145 148 146 142 147147 142 14917490612 175746175747 157109X421Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Service Notes Service Notes Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Sighting GuideParts and Service

PD22PH48STA specifications

The Poulan PD22PH48STA is a versatile and efficient lawn tractor designed for homeowners who seek a reliable solution for maintaining their lawns. With a powerful engine and user-friendly features, it has quickly become a popular choice for residential lawn care. This lawn tractor boasts a 22 horsepower, 725cc Kohler engine that delivers ample power for tackling various mowing conditions. This engine is designed for efficiency and longevity, ensuring that it can handle the rigors of regular use without compromising performance.

One of the standout features of the Poulan PD22PH48STA is its 48-inch cutting deck. This wide deck allows for efficient mowing and minimizes the number of passes required to cover large areas, making lawn maintenance quicker and more effective. The deck is made from robust materials to withstand daily wear and tear, and it has multiple height adjustment options to provide users with flexibility when it comes to grass length.

The mower is equipped with a hydrostatic transmission, enabling smooth and effortless operation. This technology allows users to change speeds without having to shift gears manually, providing a more comfortable and efficient mowing experience. The hydrostatic transmission is particularly useful when navigating complex terrains and tight spaces, where precise control is essential.

Another impressive characteristic of the Poulan PD22PH48STA is its turning radius. With a tight turning radius, this lawn tractor allows users to maneuver easily around obstacles, flower beds, and trees, contributing to a cleaner and more precise cut. The comfortable operator’s seat and ergonomic controls enhance the overall user experience, providing ample support during extended mowing sessions.

In addition, the PD22PH48STA features a durable frame and heavy-duty wheels that provide stability and traction on various surfaces, ensuring it remains reliable on uneven terrain. The mower's easy access to maintenance points simplifies upkeep, allowing users to keep their equipment in peak condition with minimal effort.

Overall, the Poulan PD22PH48STA combines power, efficiency, and user-friendly features into a state-of-the-art lawn tractor that stands out in the market. Its focus on performance and comfort makes it a strong contender for dedicated homeowners looking to achieve a well-maintained lawn with ease.
Top Page Image Contents