Poulan PD22PH48STA owner manual To Adjust Brake See Fig, To Replace Motion Drive Belt See Fig

Page 21

SERVICE AND ADJUSTMENTS

TO ADJUST BRAKE (See Fig. 25)

Your tractor is equipped with an adjustable brake system which is mounted on the side of the transaxle.

If tractor requires more than six (6) feet stopping distance at high speed in highest gear on a level dry concrete or paved surface, then brake must be adjusted.

Depress clutch/brake pedal and engage parking brake.

Measure distance between brake operating arm and nut “A” on brake rod.

If distance is other than 1-9/16", loosen jam nut and turn nut “A” until distance becomes 1-9/16". Retighten jam nut against nut “A”.

Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than six (6) feet in highest gear, further maintenance is necessary. Contact your nearest au- thorized service center/department.

WITH PARKING BRAKE “ENGAGED”

 

NUT

 

1-9/16"

“A”

JAM NUT

 

 

OPERATING

ARM

DO NOT TOUCH THIS NUT. IF FURTHER BRAKE ADJUST- MENT IS NECESSARY CONTACT YOUR NEAREST AUTHORIZED SERVICE CENTER/DEPARTMENT

FIG. 25

TO REPLACE MOTION DRIVE BELT (See Fig. 26)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

Remove mower (See “TO REMOVE MOWER” in this section of this manual.)

Remove belt from stationary idler and clutching idler.

Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades.

Pull belt toward front of tractor and remove downward from around engine pulley.

Install new belt by reversing above procedure.

ENGINE

PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

TRANSMISSION

INPUT PULLEY

FIG. 26

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See “PURGE TRANSMIS- SION” in the Operation section of this manual.

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT(See Fig. 27)

The motion control lever has been preset at the factory and adjustment should not be necessary.

Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

Start engine and move motion control lever until tractor does not move forward or backward.

Hold motion control lever in that position and turn engine off.

While holding motion control lever in place, loosen the adjustment bolt.

Move motion control lever to the neutral (N) (lock gate) position.

Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

Loosen the adjustment bolt.

Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

Tighten adjustment bolt securely.

Start engine and test.

If tractor still creeps, repeat above steps until satisfied.

21

Image 21
Contents PR17H42STC Safe Operation Practices for Ride-On Mowers Safety RulesBecome ALERT!!! Your Safety is IN- Volved Table of Contents Unassembled Parts Steering Wheel SeatSlope Sheet Tools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig Check Tire Pressure To SET UP Your Mower for MulchingCheck Deck Levelness To Convert to Bagging or DischargingOperation Know Your Tractor To Adjust Mower Cutting Height See Fig Stopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control See FigTo Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMulching Mowing Tips Mowing TipsCustomer Responsibilities Lubrication ChartGeneral Recommendations Before Each USETractor Engine Cleaning MufflerSpark Plugs To Install Mower See Fig Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigBelt Removal Transmission REMOVAL/REPLACEMENT To Adjust Brake See FigTransaxle Motion Control Lever Neutral ADJUSTMENTSee Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig To Adjust Steering Wheel AlignmentReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb Interlocks and RelaysTo Replace Fuse Other StorageFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number PR17H42STC Schematic2122 ElectricalKEY Part Description Chassis 174619 Drive 175578 175765175461 175556Steering Assembly 177876 175121175146 175118Seat Assembly Wheels and Tires Decals178206 178219Optional Equipment EngineSpark Arrester 8113170551 Control Th/ch Flag 143 159 144 150 145 148 146 142 147 Mower Deck147 142 149175746 17490612175747 157109X421Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Service Notes Service Notes Limited Warranty Sighting Guide Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PD22PH48STA specifications

The Poulan PD22PH48STA is a versatile and efficient lawn tractor designed for homeowners who seek a reliable solution for maintaining their lawns. With a powerful engine and user-friendly features, it has quickly become a popular choice for residential lawn care. This lawn tractor boasts a 22 horsepower, 725cc Kohler engine that delivers ample power for tackling various mowing conditions. This engine is designed for efficiency and longevity, ensuring that it can handle the rigors of regular use without compromising performance.

One of the standout features of the Poulan PD22PH48STA is its 48-inch cutting deck. This wide deck allows for efficient mowing and minimizes the number of passes required to cover large areas, making lawn maintenance quicker and more effective. The deck is made from robust materials to withstand daily wear and tear, and it has multiple height adjustment options to provide users with flexibility when it comes to grass length.

The mower is equipped with a hydrostatic transmission, enabling smooth and effortless operation. This technology allows users to change speeds without having to shift gears manually, providing a more comfortable and efficient mowing experience. The hydrostatic transmission is particularly useful when navigating complex terrains and tight spaces, where precise control is essential.

Another impressive characteristic of the Poulan PD22PH48STA is its turning radius. With a tight turning radius, this lawn tractor allows users to maneuver easily around obstacles, flower beds, and trees, contributing to a cleaner and more precise cut. The comfortable operator’s seat and ergonomic controls enhance the overall user experience, providing ample support during extended mowing sessions.

In addition, the PD22PH48STA features a durable frame and heavy-duty wheels that provide stability and traction on various surfaces, ensuring it remains reliable on uneven terrain. The mower's easy access to maintenance points simplifies upkeep, allowing users to keep their equipment in peak condition with minimal effort.

Overall, the Poulan PD22PH48STA combines power, efficiency, and user-friendly features into a state-of-the-art lawn tractor that stands out in the market. Its focus on performance and comfort makes it a strong contender for dedicated homeowners looking to achieve a well-maintained lawn with ease.