Poulan PD20H42STA owner manual Mowing Tips, Purge Transmission, Automatic Transmission Warm UP

Page 14

OPERATION

AUTOMATIC TRANSMISSION WARM UP

•Before driving the unit in cold weather, the transmission should be warmed up as follows:

•Be sure the tractor is on level ground.

•Place the motion control lever in neutral. Release the parking brake and let the clutch/brake

slowly return to operating position.

•Allow one minute for transmission to warm up. This can be done during the engine warm up period.

•The attachments can be used during the engine warm- up period after the transmission has been warmed up and may require the choke control be pulled out slightly.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

PURGE TRANSMISSION

CAUTION: Never engage or disengage freewheel lever while the engine is run- ning.

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de- veloped during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

•Place tractor safely on level surface with engine off and parking brake set.

•Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. With motion control lever in neutral (N) position, slowly dis- engage clutch/brake pedal.

•Move motion control lever to full forward position and hold for five (5) seconds. Move lever to full reverse position and hold for five (5) seconds. Repeat this procedure three (3) times.

NOTE: During this procedure there will be no movement of drive wheels. The air is being removed from hydraulic drive system.

•Move motion control lever to neutral (N) position. Shut- off engine and set parking brake.

•Engage transmission by placing freewheel control in driving position (See “TO TRANSPORT” in this section of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal.

•Slowly move motion control lever forward, after the tractor moves approximately five (5) feet, slowly move motion control lever to reverse position. After the trac- tor moves approximately five (5) feet return the mo- tion control lever to the neutral (N) position. Repeat this procedure with the motion control lever three (3) times.

•Your transmission is now purged and now ready for normal operation.

MOWING TIPS

•Mower should be properly leveled for best mowing per- formance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

•The left hand side of mower should be used for trim- ming.

•Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the machine. This will result in a more even distribution of clippings and more uniform cutting.

•When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 10).

FIG. 10

•If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.

•Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

•Always operate engine at full throttle when mow- ing to assure better mowing performance and proper discharge of material. Regulate ground speed by se- lecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

•When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents PD20H42STA Safety Rules Safety Rules Table of Contents Slope Sheet Unassembled PartsSteering Wheel Seat To Remove Tractor from CAR- TON AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig HOW to SET UP Your TractorInstall Seat See Fig Check Tire Pressure To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Transport See FigsCheck Engine OIL Level Before Starting the EngineTowing Carts and Other ATTACH- Ments ADD GasolineAutomatic Transmission Warm UP Mowing TipsPurge Transmission Mulching Mowing Tips Service Dates MaintenanceLubrication Chart General RecommendationsTractor Transaxle Cooling EngineBelts Transaxle Pump FluidCleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Replace Mower Blade Drive Belt See Fig To Adjust Steering Wheel ALIGN- Ment Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral Adjustment See Fig Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Start Engine with a Weak Battery See FigReplacing Battery See Figs Interlocks and RelaysTo Adjust Choke Control See Fig To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable See Fig To Adjust CarburetorFuel System StorageOther Engine OILTroubleshooting Points OFF NON-REMOVABLE Connections Removable SchematicTractor - Model Number PD20H42STA Product no 56 Electrical 2441KEY Part Description Chassis 185949 202 Drive212 116 150KEY Part NO. NO. Description Steering Assembly 180656 Wheel Steering Seat Assembly 157032 Decal Oper DecalsWheels and Tires Engine 170771 Control, Throttle Mower Deck 180532 Bracket Asm Noseroller LH 182032X42172140506 Bolt Mower Lift 178981 Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PD20H42STA specifications

The Poulan PD20H42STA is a standout model in the realm of residential riding lawn mowers, designed to deliver exceptional performance for homeowners looking to maintain their lawns with ease. With a robust 20-horsepower Briggs & Stratton engine, the PD20H42STA provides ample power to tackle various terrain types, making it suitable for lawns of all sizes. The engine is designed for reliability and ease of starting, ensuring that homeowners can get to work without delay.

One of the key features of the Poulan PD20H42STA is its 42-inch cutting deck, which is ideal for efficiently trimming large areas without compromising maneuverability. The deck is crafted from durable steel, enhancing its longevity and resistance to wear and tear. This wide cutting deck can also be adjusted to several cutting heights, ranging from one to four inches, allowing users to customize their mowing experience based on their lawn's specific needs.

The PD20H42STA employs an innovative hydrostatic transmission system, which provides smooth and effortless speed control. This feature allows operators to accelerate and decelerate seamlessly, enhancing the overall mowing experience. The pedal-operated system eliminates the need for shifting gears, making it user-friendly for both experienced and novice riders.

Ergonomics and comfort have also been prioritized in the design of the Poulan PD20H42STA. The plush, high-back seat provides excellent support for extended mowing sessions, while the easy-to-reach controls ensure that users can operate the mower without straining. Additionally, the model includes a tight turning radius, allowing it to navigate around obstacles with precision.

Another notable characteristic of the PD20H42STA is its versatility. It supports various attachments and accessories, such as baggers, mulchers, and snow blades, making it a multifaceted tool for year-round lawn care and landscaping needs. This adaptability enhances its value and utility for homeowners seeking to maximize their investment.

In summary, the Poulan PD20H42STA is engineered for performance and practicality, making it an excellent choice for any homeowner looking to simplify lawn maintenance. With its powerful engine, durable construction, user-friendly features, and versatile capabilities, it stands out as a reliable lawn care solution that combines comfort with efficiency, ultimately leading to a beautifully manicured yard.
Top Page Image Contents