Tractor

MAINTENANCE

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See“PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent ﬂat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without ﬁrst setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 12)

•Raise mower to highest position to allow access to blades.

•Remove blade bolt, lock washer and ﬂat washer securing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble blade bolt, lock washer and ﬂat washer in exact order as shown.

•Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

	TRAILING	MANDREL
	TRAILING	ASSEMBLY
	EDGE UP	ASSEMBLY
	EDGE UP
	BLADE
		CENTER
		HOLE

FLAT WASHER

LOCK WASHER

STAR

BLADE BOLT (GRADE 8)*

*A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 12

TO SHARPEN BLADE (See Fig. 13)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An un- balanced blade will cause excessive vibration and eventual damage to mower and engine.

•The blade can be sharpened with a ﬁle or on a grind- ing wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer).

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

	CENTER HOLE
5/8" BOLT	BLADE
OR PIN

FIG. 13

BATTERY

Your tractor has a battery charging system which is sufﬁcient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

PD20H42STA specifications

The Poulan PD20H42STA is a standout model in the realm of residential riding lawn mowers, designed to deliver exceptional performance for homeowners looking to maintain their lawns with ease. With a robust 20-horsepower Briggs & Stratton engine, the PD20H42STA provides ample power to tackle various terrain types, making it suitable for lawns of all sizes. The engine is designed for reliability and ease of starting, ensuring that homeowners can get to work without delay.

One of the key features of the Poulan PD20H42STA is its 42-inch cutting deck, which is ideal for efficiently trimming large areas without compromising maneuverability. The deck is crafted from durable steel, enhancing its longevity and resistance to wear and tear. This wide cutting deck can also be adjusted to several cutting heights, ranging from one to four inches, allowing users to customize their mowing experience based on their lawn's specific needs.

The PD20H42STA employs an innovative hydrostatic transmission system, which provides smooth and effortless speed control. This feature allows operators to accelerate and decelerate seamlessly, enhancing the overall mowing experience. The pedal-operated system eliminates the need for shifting gears, making it user-friendly for both experienced and novice riders.

Ergonomics and comfort have also been prioritized in the design of the Poulan PD20H42STA. The plush, high-back seat provides excellent support for extended mowing sessions, while the easy-to-reach controls ensure that users can operate the mower without straining. Additionally, the model includes a tight turning radius, allowing it to navigate around obstacles with precision.

Another notable characteristic of the PD20H42STA is its versatility. It supports various attachments and accessories, such as baggers, mulchers, and snow blades, making it a multifaceted tool for year-round lawn care and landscaping needs. This adaptability enhances its value and utility for homeowners seeking to maximize their investment.

In summary, the Poulan PD20H42STA is engineered for performance and practicality, making it an excellent choice for any homeowner looking to simplify lawn maintenance. With its powerful engine, durable construction, user-friendly features, and versatile capabilities, it stands out as a reliable lawn care solution that combines comfort with efficiency, ultimately leading to a beautifully manicured yard.