Poulan PD20H42STA HOW to SET UP Your Tractor, Install Seat See Fig, Check Battery See Fig

Page 7

ASSEMBLY

HOW TO SET UP YOUR TRACTOR

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

SEAT

SEAT PAN

SHOULDER

BOLT

FLAT WASHER

ADJUSTMENT

KNOB

FIG. 2

CHECK BATTERY (See Fig. 3)

•Lift seat pan to raised position.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instructions).

SEAT PAN

LABEL

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place freewheel control in "transmission disengaged position" (See “TO TRANSPORT” in the Operation section of this manual).

•Roll tractor forward off skid.

•Remove banding holding the deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been com- pleted.

•Check engine oil level and fill fuel tank with gasoline.

•Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual).

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

•Place motion control lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Start the engine.After engine has started, move throttle control to idle position.

•Release parking brake.

•Slowly move the motion control lever forward and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

•Turn ignition key to "STOP" position.

Continue with the instructions that follow.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents PD20H42STA Safety Rules Safety Rules Table of Contents Steering Wheel Seat Unassembled PartsSlope Sheet Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CAR- TONInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Deck Levelness To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Tire PressureOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelPurge Transmission Mowing TipsAutomatic Transmission Warm UP Mulching Mowing Tips General Recommendations MaintenanceLubrication Chart Service DatesTractor Transaxle Pump Fluid EngineBelts Transaxle CoolingCleaning To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake See FigTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust Steering Wheel ALIGN- MentInterlocks and Relays To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Replace Headlight BulbTo Adjust Carburetor To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable See Fig To Adjust Choke Control See FigEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number PD20H42STA Product no 56 SchematicNON-REMOVABLE Connections Removable 2441 ElectricalKEY Part Description Chassis 185949 150 Drive212 116 202KEY Part NO. NO. Description Steering Assembly 180656 Wheel Steering Seat Assembly Wheels and Tires Decals157032 Decal Oper Engine 170771 Control, Throttle Mower Deck 72140506 Bolt 182032X421180532 Bracket Asm Noseroller LH Mower Lift 178981 Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PD20H42STA specifications

The Poulan PD20H42STA is a standout model in the realm of residential riding lawn mowers, designed to deliver exceptional performance for homeowners looking to maintain their lawns with ease. With a robust 20-horsepower Briggs & Stratton engine, the PD20H42STA provides ample power to tackle various terrain types, making it suitable for lawns of all sizes. The engine is designed for reliability and ease of starting, ensuring that homeowners can get to work without delay.

One of the key features of the Poulan PD20H42STA is its 42-inch cutting deck, which is ideal for efficiently trimming large areas without compromising maneuverability. The deck is crafted from durable steel, enhancing its longevity and resistance to wear and tear. This wide cutting deck can also be adjusted to several cutting heights, ranging from one to four inches, allowing users to customize their mowing experience based on their lawn's specific needs.

The PD20H42STA employs an innovative hydrostatic transmission system, which provides smooth and effortless speed control. This feature allows operators to accelerate and decelerate seamlessly, enhancing the overall mowing experience. The pedal-operated system eliminates the need for shifting gears, making it user-friendly for both experienced and novice riders.

Ergonomics and comfort have also been prioritized in the design of the Poulan PD20H42STA. The plush, high-back seat provides excellent support for extended mowing sessions, while the easy-to-reach controls ensure that users can operate the mower without straining. Additionally, the model includes a tight turning radius, allowing it to navigate around obstacles with precision.

Another notable characteristic of the PD20H42STA is its versatility. It supports various attachments and accessories, such as baggers, mulchers, and snow blades, making it a multifaceted tool for year-round lawn care and landscaping needs. This adaptability enhances its value and utility for homeowners seeking to maximize their investment.

In summary, the Poulan PD20H42STA is engineered for performance and practicality, making it an excellent choice for any homeowner looking to simplify lawn maintenance. With its powerful engine, durable construction, user-friendly features, and versatile capabilities, it stands out as a reliable lawn care solution that combines comfort with efficiency, ultimately leading to a beautifully manicured yard.
Top Page Image Contents