Poulan CO1842STA manual Tractor

Page 18

TRACTOR

Always observe safety rules when per- forming any maintenance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may

cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are working properly. If your trac- tor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any at- tempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any at- tempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never op- erate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL

1.Raise mower to highest position to al- low access to blades.

2.Remove blade bolt, lock washer and flat washer securing blade.

3.Install new or resharpened blade with

trailing edge up towards deck as shown. IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

4.Reassemble blade bolt, lock washer and flat washer in exact order as shown.

5.Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: Blade bolt is heat treated. If bolt needs replacing, replace only with approve bolt shown in the Repair Parts.

Flat

Trailing Edge Up

 

 

Mandrel

 

 

2

 

0

14

 

 

Blade

1

 

Assembly

Washer

 

 

 

 

 

 

Lock

 

 

 

 

Washer

 

 

 

 

Blade

 

 

 

Star

 

 

 

 

Bolt

Center Hole

 

 

 

TO SHARPEN BLADE

NOTE: We do not recommend sharp- ening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and eventual damage to mower and engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone bal- ancer. (When using a cone balancer, follow

the instructions supplied with balancer.) NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

 

 

Center

5/8" Bolt

01202

Hole

 

or Pin

Blade

 

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. How- ever, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and termi- nals can cause the battery to “leak” power.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model NO. CO1842STA Table of Contents WarrantySafety Rules General OperationII. Slope Operation IV. Service III. ChildrenDo not Safety Rules Product Specifications Customer ResponsibilitiesAPI-SF-SJ Unassembled Parts To Remove Tractor from Carton Tools Required for AssemblyHOW to SET UP Your Tractor Before Removing Tractor from SkidCheck Battery Check Tire Pressure Install Mulcher PlateTo Convert to Bagging or Discharging Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport To Operate MowerTo Operate on Hills Towing Carts and Other ATTACH- MentsCheck Engine OIL Level Before Starting the EngineTo Start Engine ADD GasolineMowing Tips Maintenance General RecommendationsBefore Each USE Tractor Engine Service and Adjustments CleaningSIDE-TO-SIDE Adjustment To Install MowerTo Level Mower Housing FRONT-TO-BACK AdjustmentTo Check and Adjust Brake To Replace Mower Blade Drive BeltTo Replace Motion Drive Belt To Start Engine with a Weak Battery To Adjust Steering Wheel ALIGN- MentTransaxle Gear Shift Lever NEU- Tral Adjustment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor Fuel System BatteryOther Engine OILTroubleshooting Chart Problem Cause CorrectionExcessive Poor grass Suggested Guide for Sighting Slopes for Safe Operation

CO1842STA specifications

The Poulan CO1842STA is a highly regarded riding lawn mower known for its robust performance and user-friendly features, making it a favorite among homeowners looking to maintain their lawns efficiently. Designed for mid-sized residential properties, this riding mower combines power, reliability, and comfort, making yard work a more manageable task.

One of the main features of the Poulan CO1842STA is its 18.5 horsepower Briggs & Stratton engine, which provides ample power to tackle thick grass and uneven terrain. The engine is designed for easy starting and consistent performance. The mower features a 42-inch cutting deck, allowing users to cover a larger area in a shorter amount of time. This size strikes a balance between maneuverability and efficiency, enabling easy navigation around trees and garden beds.

The cutting deck's height can be adjusted easily, offering six different positions to cater to various mowing preferences and grass lengths. This flexibility ensures that users can achieve the desired lawn appearance without damaging the grass. Additionally, the mower features a side discharge, which allows for efficient grass clipping dispersal.

Technologically, the Poulan CO1842STA includes a foot-operated hydrostatic transmission, which simplifies speed control. By eliminating the need for manual shifting, users can focus on steering and cutting, enhancing their overall mowing experience. The mower also features a comfortable ergonomic seat, which is crucial for long mowing sessions, reducing user fatigue.

For added convenience, the Poulan CO1842STA is equipped with a turning radius that facilitates quick and easy maneuverability in tight spaces. This feature is especially beneficial for those with intricate landscaping or numerous obstacles in their yard.

Maintenance is straightforward with this model, as it comes with a deck wash port that allows for easy cleaning of the cutting deck, promoting optimal performance and extending the life of the mower. Overall, the Poulan CO1842STA presents an impressive combination of power, comfort, and ease of use, making it a strong choice for homeowners seeking dependable lawn care equipment. Whether tackling overgrown grass or maintaining a well-manicured lawn, this riding mower stands out as a reliable partner in yard maintenance.
Top Page Image Contents