Poulan CO1842STA manual To Adjust Steering Wheel ALIGN- Ment, Front Wheel TOE-IN/CAMBER

Page 23

BELT INSTALLATION -

1.Carefully work new belt down between transaxle belt keepers and onto the input pulley.

2.Slide belt into the center span keeper.

3.Pull belt toward front of tractor and roll around the top groove of engine pulley.

4.Install belt through stationary idler and clutching idler.

5.Make sure belt is in all pulley grooves and inside all belt guides and keepers.

6.Install mower (See “TO INSTALL MOWER” in this section of manual).

Engine

Pulley

Clutching

Idler

Stationary

Idler

Center

Span

Keeper

Transaxle

Pulley

00811

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not

horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble with crossbars horizontal. Tighten securely.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS

1.Block up axle securely.

2.Remove axle cover, retaining ring and washers to allow wheel removal (rear wheels have a square key - Do not lose).

3.Repair tire and reassemble.

NOTE: On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

4.Replace washers and snap retaining ring securely in axle groove.

5.Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

TRANSAXLE GEAR SHIFT LEVER NEU- TRAL ADJUSTMENT

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

1.Make sure transaxle is in neutral (N). NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

2.Loosen adjustment bolt in front of the right rear wheel.

3.Position the gear shift lever in the neu- tral (N) position.

4.Tighten adjustment bolt securely. NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

Gearshift Lever

Retaining Washers

Ring

Axle

Cover

00663

Square Key

(Rear Wheel Only)

TO START ENGINE WITH A WEAK BATTERY

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BAT- TERY" in the MAINTENANCE section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure: IMPORTANT: Your tractor is equipped with a 12 volt system. The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles.

02239

Adjustment Bolt

Neutral

Lock Gate

 

TO ATTACH JUMPER CABLES -

1.Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short

23against tractor chassis.

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model NO. CO1842STA Warranty Table of ContentsII. Slope Operation Safety RulesGeneral Operation Do not IV. ServiceIII. Children Safety Rules API-SF-SJ Product SpecificationsCustomer Responsibilities Unassembled Parts Before Removing Tractor from Skid Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonCheck Battery Check for Proper Position of ALL Belts Install Mulcher PlateTo Convert to Bagging or Discharging Check Tire PressureOperation Know Your Tractor HOW to USE Your Tractor Towing Carts and Other ATTACH- Ments To Operate MowerTo Operate on Hills To TransportADD Gasoline Before Starting the EngineTo Start Engine Check Engine OIL LevelMowing Tips Before Each USE MaintenanceGeneral Recommendations Tractor Engine Cleaning Service and AdjustmentsFRONT-TO-BACK Adjustment To Install MowerTo Level Mower Housing SIDE-TO-SIDE AdjustmentTo Replace Motion Drive Belt To Check and Adjust BrakeTo Replace Mower Blade Drive Belt Front Wheel TOE-IN/CAMBER To Adjust Steering Wheel ALIGN- MentTransaxle Gear Shift Lever NEU- Tral Adjustment To Start Engine with a Weak BatteryTo Adjust Carburetor Engine OIL BatteryOther Fuel SystemProblem Cause Correction Troubleshooting ChartExcessive Poor grass Suggested Guide for Sighting Slopes for Safe Operation

CO1842STA specifications

The Poulan CO1842STA is a highly regarded riding lawn mower known for its robust performance and user-friendly features, making it a favorite among homeowners looking to maintain their lawns efficiently. Designed for mid-sized residential properties, this riding mower combines power, reliability, and comfort, making yard work a more manageable task.

One of the main features of the Poulan CO1842STA is its 18.5 horsepower Briggs & Stratton engine, which provides ample power to tackle thick grass and uneven terrain. The engine is designed for easy starting and consistent performance. The mower features a 42-inch cutting deck, allowing users to cover a larger area in a shorter amount of time. This size strikes a balance between maneuverability and efficiency, enabling easy navigation around trees and garden beds.

The cutting deck's height can be adjusted easily, offering six different positions to cater to various mowing preferences and grass lengths. This flexibility ensures that users can achieve the desired lawn appearance without damaging the grass. Additionally, the mower features a side discharge, which allows for efficient grass clipping dispersal.

Technologically, the Poulan CO1842STA includes a foot-operated hydrostatic transmission, which simplifies speed control. By eliminating the need for manual shifting, users can focus on steering and cutting, enhancing their overall mowing experience. The mower also features a comfortable ergonomic seat, which is crucial for long mowing sessions, reducing user fatigue.

For added convenience, the Poulan CO1842STA is equipped with a turning radius that facilitates quick and easy maneuverability in tight spaces. This feature is especially beneficial for those with intricate landscaping or numerous obstacles in their yard.

Maintenance is straightforward with this model, as it comes with a deck wash port that allows for easy cleaning of the cutting deck, promoting optimal performance and extending the life of the mower. Overall, the Poulan CO1842STA presents an impressive combination of power, comfort, and ease of use, making it a strong choice for homeowners seeking dependable lawn care equipment. Whether tackling overgrown grass or maintaining a well-manicured lawn, this riding mower stands out as a reliable partner in yard maintenance.
Top Page Image Contents