Poulan BB185H42YT manual Transmission REMOVAL/REPLACEMENT, To Adjust Steering Wheel ALIGN- Ment

Page 22

SERVICE AND ADJUSTMENTS

While holding motion control lever in place, loosen the adjustment bolt.

Move motion control lever to the neutral (N) (lock gate) position.

Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

Loosen the adjustment bolt.

Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

Tighten adjustment bolt securely.

Start engine and test.

If tractor still creeps, repeat above steps until satis- fied.

MOTION CONTROL

NEUTRAL

LEVER

LOCK GATE

 

ADJUSTMENT

BOLT

FIG. 23

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See“PURGETRANSMISSION” in the Operation section of this manual.

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor.If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 24

TO START ENGINE WITH A WEAK BATTERY (See Fig. 25)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

BLACK cable first from chassis and then from the fully charged battery.

RED cable last from both batteries.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 24)

Block up axle securely.

Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

Repair tire and reassemble.

On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

Replace washers and snap retaining ring securely in axle groove.

Replace axle cover.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

22

FIG. 25

Image 22
Contents BB185H42YT Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceIV. Towing Table of Contents Key Unassembled PartsSteering Wheel Seat Slope SheetTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsTo Transport See Figs Before Starting the EngineADD Gasoline Check Engine OIL LevelPurge Transmission Mowing TipsAutomatic Transmission Warm UP General Recommendations MaintenanceLubrication Chart Before Each USETo Sharpen Blade See Fig TractorBlade Removal See Fig Check Operator Presence SystemEngine Cleaning To Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal To Adjust Brake To Check and Adjust Brake See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Engine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

BB185H42YT specifications

The Poulan BB185H42YT is a versatile and efficient riding lawn mower designed to meet the needs of homeowners with medium to large yards. This mower combines ease of use with advanced technology, making it an ideal choice for those seeking performance and reliability in their lawn care routine.

One of the standout features of the BB185H42YT is its powerful engine. It is equipped with an 18.5 HP Briggs & Stratton engine that provides robust performance, enabling the mower to tackle tough grass and uneven terrain with ease. The engine's design ensures efficient fuel consumption, giving users peace of mind while mowing over larger areas without constantly refueling.

The mower features a 42-inch cutting deck, allowing for wider cutting paths and reducing the overall time spent mowing. The deck is constructed from durable steel, ensuring longevity and resilience against the rigors of regular use. Additionally, the BB185H42YT offers multiple cutting height adjustments, enabling homeowners to customize their lawn’s appearance according to their specific requirements.

One of the key technologies present in the Poulan BB185H42YT is the automatic transmission system. This feature allows for smooth speed adjustments while mowing, eliminating the need for manual gear shifting. As a result, users can focus on their mowing tasks without the distraction of managing speeds, ensuring a seamless mowing experience.

Maneuverability is another highlight of the BB185H42YT. With a tight turning radius, this mower can navigate around obstacles, flower beds, and trees with relative ease. This makes it an excellent option for yards with intricate layouts, saving time and effort in achieving a neat and well-manicured lawn.

Comfort is paramount in the design of the BB185H42YT. The mower comes with an adjustable high-back seat, providing ample support during extended mowing sessions. The ergonomic steering wheel design and easy-to-reach controls enhance user comfort, ensuring that mowing duties are less of a chore.

In terms of maintenance, this model is designed with user convenience in mind. The mower features easy-access components for routine checks and maintenance tasks, allowing owners to keep the machine in optimal condition without hassle.

In summary, the Poulan BB185H42YT stands out due to its powerful engine, wide cutting deck, automatic transmission, and user-friendly design. It is an excellent choice for homeowners looking for a reliable and efficient riding lawn mower capable of delivering exceptional results with minimal effort. With its combination of features and technologies, the BB185H42YT makes lawn care a manageable and enjoyable task.