Poulan 96012010200 Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1) 1/2" wrench

Utility knife

(1) 3/4" wrench

Tire pressure gauge

Pliers

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSERT

5/16 HEX BOLT

5/16 LOCK WASHER

LARGE FLAT

WASHER

STEERING

 

WHEEL

STEERING

 

 

BOOT

ADAPTER

 

 

EXTENSION

 

SHAFT

LOWER

STEERING

SHAFT

FIG. 1

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment bolt.

•Remove adjustment bolt, lock washer and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjust- ment bolt, lockwasher and flat washer loosely. Do not tighten

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment bolt securely.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PO17542LT ModelGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Steering WheelTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidTo Check Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Reverse Operation System ROSTo Operate Mower See Fig To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips General Recommendations MaintenanceMaintenance ScheduleTractor Blade Removal See FigEngine BatteryTransaxle Maintenance BeltsAIR Filter CleaningClean AIR Screen MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionExcessive Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

433471, 96012010200 specifications

The Poulan 96012010200,433471 is a robust and reliable chainsaw designed for both professional landscapers and diligent homeowners. Known for its powerful performance, this chainsaw stands out due to its combination of advanced technology and user-friendly features, making it suitable for a variety of cutting tasks.

One of the key features of the Poulan 96012010200,433471 is its potent engine. With a highly efficient two-stroke design, it delivers ample power to tackle even the toughest jobs. This allows the chainsaw to cut through thick branches and trees with ease, ensuring quick and efficient results. Additionally, the engine's design aids in reducing emissions and noise, making it an environmentally friendly choice for users who are conscious of their carbon footprint.

The chainsaw’s ergonomic design is another significant highlight. Weighing in at a manageable level, it provides an optimal balance for ease of maneuverability during operation. The handle is designed with comfort in mind, featuring anti-vibration technology to reduce fatigue and ensure stability while cutting. This thoughtful ergonomics allows users to maintain control over long working sessions without straining their hands or arms.

Another characteristic that makes the Poulan 96012010200,433471 exceptional is its ease of use. The chainsaw comes equipped with a tool-less chain tensioning system, allowing users to adjust the chain quickly and efficiently without the need for special tools. This feature is particularly beneficial for those who might encounter unexpected situations in the field, ensuring downtime is minimized.

Safety features also prioritize the user's well-being. The chainsaw includes a chain brake that activates in the event of kickback, providing immediate stopping action. Furthermore, the throttle lock prevents accidental acceleration, which can help prevent accidents during operation.

Users will appreciate the chainsaw's durable construction, made from high-quality materials designed to withstand wear and tear over time. The Poulan 96012010200,433471 is built not just for performance, but also for longevity. With its combination of power, comfort, and safety features, this chainsaw is an excellent choice for anyone looking to invest in a reliable piece of outdoor equipment that promises to deliver exceptional results in their cutting tasks.
Top Page Image Contents