Poulan 96012010200, 433471 manual Transaxle Gear Shift Lever NEUTRAL- Adjustment See Fig

Page 22

SERVICE AND ADJUSTMENTS

TRANSAXLE GEAR SHIFT LEVER NEUTRAL- ADJUSTMENT (See Fig. 19)

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral (N).

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) posi- tion.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

 

NEUTRAL

GEARSHIFT LEVER

LOCK GATE

 

 

ADJUSTMENT

 

BOLT

FIG. 19

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 20

TO START ENGINE WITH A WEAK BATTERY (See Fig. 21)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 20)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

22

FIG. 21

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PO17542LT ModelGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Steering WheelTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidTo Check Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Reverse Operation System ROSTo Operate Mower See Fig To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips General Recommendations MaintenanceMaintenance ScheduleTractor Blade Removal See FigEngine BatteryTransaxle Maintenance BeltsAIR Filter CleaningClean AIR Screen MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionExcessive Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

433471, 96012010200 specifications

The Poulan 96012010200,433471 is a robust and reliable chainsaw designed for both professional landscapers and diligent homeowners. Known for its powerful performance, this chainsaw stands out due to its combination of advanced technology and user-friendly features, making it suitable for a variety of cutting tasks.

One of the key features of the Poulan 96012010200,433471 is its potent engine. With a highly efficient two-stroke design, it delivers ample power to tackle even the toughest jobs. This allows the chainsaw to cut through thick branches and trees with ease, ensuring quick and efficient results. Additionally, the engine's design aids in reducing emissions and noise, making it an environmentally friendly choice for users who are conscious of their carbon footprint.

The chainsaw’s ergonomic design is another significant highlight. Weighing in at a manageable level, it provides an optimal balance for ease of maneuverability during operation. The handle is designed with comfort in mind, featuring anti-vibration technology to reduce fatigue and ensure stability while cutting. This thoughtful ergonomics allows users to maintain control over long working sessions without straining their hands or arms.

Another characteristic that makes the Poulan 96012010200,433471 exceptional is its ease of use. The chainsaw comes equipped with a tool-less chain tensioning system, allowing users to adjust the chain quickly and efficiently without the need for special tools. This feature is particularly beneficial for those who might encounter unexpected situations in the field, ensuring downtime is minimized.

Safety features also prioritize the user's well-being. The chainsaw includes a chain brake that activates in the event of kickback, providing immediate stopping action. Furthermore, the throttle lock prevents accidental acceleration, which can help prevent accidents during operation.

Users will appreciate the chainsaw's durable construction, made from high-quality materials designed to withstand wear and tear over time. The Poulan 96012010200,433471 is built not just for performance, but also for longevity. With its combination of power, comfort, and safety features, this chainsaw is an excellent choice for anyone looking to invest in a reliable piece of outdoor equipment that promises to deliver exceptional results in their cutting tasks.
Top Page Image Contents