Poulan 418757 manual Service and Adjustments, To Remove Mower See Fig, To Install Mower See Fig

Page 19

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST- MENTS:

•Depress clutch/brake pedal fully and set parking brake.

•Place gearshift lever in neutral (N) position.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER (See Fig. 15)

Mower will be easier to remove from the right side of tractor.

•Place attachment clutch in “DISENGAGED” position.

•Move attachment lift lever forward to lower mower to its lowest position.

•Roll belt off engine pulley.

•Remove small retainer spring, and remove clutch spring off pulley bolt.

•Remove large retainer spring, slide collar off and push housing guide out of bracket.

•Disconnect anti-swaybar from chassis bracket by re- moving retainer spring.

•Disconnect suspension arms from rear deck brackets by removing retainer springs.

•Disconnect front links from deck by removing retainer springs.

•Raise lift lever to raise suspension arms. Slide mower out from under tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER DECK IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONT LINKS AND HOOK THE CLUTCH SPRING INTO SQUARE HOLE IN FRAME.

TO INSTALL MOWER (See Fig. 15)

•Raise attachment lift lever to its highest position.

•Slide mower under tractor with deflector shield to right side of tractor.

•Lower lift lever to its lowest position.

•Connect front links to mower deck and secure with retainer springs..

•Connect suspension arms to rear deck brackets and secure with retainer springs.

•Connect anti-swaybar to chassis bracket and secure with retainer spring.

•Push clutch cable housing guide into bracket, slide col- lar onto guide and secure with large retainer spring.

•Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring.

•Install belt onto engine pulley.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

 

SMALL RETAINER SPRING

 

 

 

 

CLUTCH SPRING

 

 

 

 

FLAT WASHER

 

 

SQUARE HOLE

SMALL RETAINER SPRING

 

SUSPENSION

ENGINE PULLEY

 

 

 

ARMS

 

 

 

 

CLUTCH SPRING

 

 

 

 

 

 

 

FRONT LINK

RETAINER SPRING

 

 

 

 

ANTI-SWAY BAR

 

 

 

 

 

 

 

 

RETAINER SPRINGS

COLLAR

 

 

 

(BOTH SIDES)

HOUSING GUIDE

LARGE RETAINER

 

 

 

SPRING

BRACKET

 

DEFLECTOR SHIELD

 

 

 

 

 

 

 

FIG. 15

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Lawn Tractor Model PBA19542LTXII. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIII. Children ServiceIV. Towing Table of Contents Keys Unassembled PartsSteering Wheel SeatBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig Install Seat See FigCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Operate Mower See FigTo Operate on Hills ADD Gasoline Before Starting the EngineTo Transport Check Engine OIL LevelMowing Tips Check Brake Operation Check Tire Pressure MaintenanceGeneral Recommendations Before Each USECheck Operator Presence System TractorBlade Removal See Fig To Sharpen Blade See FigEngine Muffler CleaningClean AIR Screen AIR FilterTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingRecheck side-to-side adjustment To Replace Motion Drive Belt See Fig Belt InstallationTo Check Brake To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Start Engine with a Weak Battery See Fig To Adjust Steering Wheel ALIGN- MentInterlocks and Relays To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Stevens Creek Road Terry Fox Way Augusta, GA 30907 USA Outdoor Products Customer Service DeptHOP Canada contactService Notes Suggested Guide for Sighting Slopes for Safe Operation Parts and Service Changere DE Pièces LES ET L’ENTRETIEN UNE Pliez EST Ceci Degrés Suivant LES’ENTRETIEN Remarques Autorisé Dept Service Customer Products Outdoor Canada AuGarantie cette de exclus sont normal l’entretien et Conducteur le lorsque Dépannage DE GuideLame de mandrin le Remplacez Tordu est lame de mandrin Un Moteur EntreposageTracteur Moteur Reglages ET RevisionVoir Vitesses DE Boîte LA DE Mentge Rossage -AVANT/CAR Roues DES ConvergenceLA DE L’ALIGNEMENT Régler Pour Fig la’EN Courroie LA Remplacer Pour Fig la VoirCourroie Acer Rempl Pour 17 .FIG Tondeuse DE Boîtier LE Niveler Pour19 .FIG 18 .FIG15 .FIG Tracteur’AIR Tamis LE Nettoyer Entretien’ALLUMAGE Bougie AIR À FiltreTrapézoïdales Courroies Sionmistrans LA DE Moteur FluideTransmission LA DE Refroidissement Fig la Voir Lame LA AffilerEN Fonctionnement DE Système ET Fig la Voir Lame LA EnleverUtilisation Chaque Avant Recommandations LESGénérales Lubrification DE TableauTondre DE Conseils UtilisationAvec marcher le-faites moteur, le démarrez vous Quand Moteur LE Démarrer DE Avant Fonction DE Système DU Utilisation Pentes LES Dans Utiliser PourMAR EN Fonctionnement DE Système Fig la Voir Arrêter Pour GAZ DES Commande LA Utiliser PourTeurtrac Votre Utiliser Comment Reculer Pour ET Avancer PourLSW02838 ’EMBRAYAGE PA LA DE Tracteur LE Retirer Pour MontageDesmancom des tionfonc la et Tionsec la Voir Conduisant LE EN LetteCom des fonction la et mentceplalem Fig la Voir Siège LE InstallerVotre Monter Comment DesmanPalette LA DU Tracteur LE Sortir PourToncar Pente-Guide Montées NON PiécesCCA .MIN AMP/HR SommaireClient DU Responsabilités Produit DE SpécificationsGénéral Entretien EntretienRemorquage EnfantsTracteurs des sécurité toute en l’utilisation pour Conseils TESPEN LES Dans Fonctionnement Général FonctionnementCom.poulan.www web site notre Visitez LTX19542PBA ModèleAUX Imprimé

418757, 96012008400 specifications

The Poulan 96012008400 418757 is a robust and reliable chainsaw that has garnered attention among both casual users and professional arborists. Designed primarily for cutting firewood and maintaining trees, this chainsaw is a quintessential tool for outdoor enthusiasts and homeowners alike.

One of the standout features of this model is its powerful engine. Fitted with a 20-inch bar, the chainsaw is equipped to handle larger cutting tasks with ease. The engine delivers strong performance, allowing for efficient cutting through hardwood and softwood alike, making it versatile for various applications. Furthermore, the chainsaw's lightweight design ensures that it is manageable for extended use, offering comfort during long periods of operation.

The Poulan 96012008400 418757 is designed with advanced technologies that enhance user safety and operational efficiency. It features an automatic oiler that provides constant lubrication to the chain, ensuring a smooth cutting experience while reducing wear and tear. This technology minimizes the need for manual adjustments, allowing users to focus more on their tasks. Additionally, the chain brake feature is a crucial safety element, designed to protect the user in the event of kickback, allowing for a quick stop of the chain movement.

Another impressive characteristic of the Poulan chainsaw is its easy-start system. This technology reduces the effort required to start the engine, making it accessible for all users, regardless of their experience level. The ergonomic design of the handles also contributes to user comfort, with rubber grips that absorb vibration, preventing fatigue during longer cutting sessions.

Maintenance is simplified with easy-access air filters and spark plugs, allowing users to keep their saw in top condition without the hassle of complicated disassemblies. The Poulan 96012008400 418757 also boasts a durable construction, featuring a high-quality plastic body that resists wear from environmental factors, extending the life of the equipment.

In summary, the Poulan 96012008400 418757 chainsaw combines power, safety, and user-friendly design, making it an outstanding choice for anyone in need of a reliable cutting tool. Its blend of advanced features and durability ensures that it is well-equipped to tackle a variety of cutting tasks with confidence and efficiency.
Top Page Image Contents