Poulan 96012008400 Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

3/4" wrench

Pliers

(1)

1/2" wrench

Tire pressure gauge

 

 

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dashed lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

Insert

5/16 Hex

Bolt

5/16 Lock

Washer

Large

Flat

Washer

Steering

Wheel

Steering Boot

Adapter

Extension

Shaft

Lower

Steering

Shaft

FIG. 1

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Model PBA19542LTX Lawn TractorGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationService III. ChildrenIV. Towing Table of Contents Seat Unassembled PartsSteering Wheel KeysTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidInstall Seat See Fig Check Battery See FigCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Reverse Operation System ROSTo Operate on Hills Check Engine OIL Level Before Starting the EngineTo Transport ADD GasolineMowing Tips Before Each USE MaintenanceGeneral Recommendations Check Brake Operation Check Tire PressureTo Sharpen Blade See Fig TractorBlade Removal See Fig Check Operator Presence SystemEngine AIR Filter CleaningClean AIR Screen MufflerTo Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigRecheck side-to-side adjustment To Replace Mower Blade Drive Belt See Fig Belt InstallationTo Check Brake To Replace Motion Drive Belt See FigTo Adjust Steering Wheel ALIGN- Ment Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Carburetor Interlocks and RelaysFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Canada contact Outdoor Products Customer Service DeptHOP Stevens Creek Road Terry Fox Way Augusta, GA 30907 USAService Notes Suggested Guide for Sighting Slopes for Safe Operation Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Degrés Suivant LES UNE Pliez EST Ceci’ENTRETIEN Remarques Dept Service Customer Products Outdoor Canada Au AutoriséGarantie cette de exclus sont normal l’entretien et Dépannage DE Guide Conducteur le lorsqueLame de mandrin le Remplacez Tordu est lame de mandrin Un Entreposage MoteurTracteur Reglages ET Revision MoteurFig la Rossage -AVANT/CAR Roues DES ConvergenceLA DE L’ALIGNEMENT Régler Pour Voir Vitesses DE Boîte LA DE MentgeFig la Voir ’EN Courroie LA Remplacer PourCourroie Acer Rempl Pour 18 .FIG Tondeuse DE Boîtier LE Niveler Pour19 .FIG 17 .FIGTracteur 15 .FIGAIR À Filtre Entretien’ALLUMAGE Bougie ’AIR Tamis LE NettoyerFig la Voir Lame LA Affiler Sionmistrans LA DE Moteur FluideTransmission LA DE Refroidissement Trapézoïdales CourroiesFig la Voir Lame LA Enlever EN Fonctionnement DE Système ETLubrification DE Tableau Recommandations LESGénérales Utilisation Chaque AvantUtilisation Tondre DE ConseilsAvec marcher le-faites moteur, le démarrez vous Quand Moteur LE Démarrer DE Avant Pentes LES Dans Utiliser Pour Fonction DE Système DU UtilisationMAR EN Fonctionnement DE Système Reculer Pour ET Avancer Pour GAZ DES Commande LA Utiliser PourTeurtrac Votre Utiliser Comment Fig la Voir Arrêter PourLSW02838 ’EMBRAYAGE Tionsec la Voir Conduisant LE EN Lette MontageDesmancom des tionfonc la et PA LA DE Tracteur LE Retirer PourDesman Fig la Voir Siège LE InstallerVotre Monter Comment Com des fonction la et mentceplalemDU Tracteur LE Sortir Pour Palette LAToncar Montées NON Piéces Pente-GuideProduit DE Spécifications SommaireClient DU Responsabilités CCA .MIN AMP/HREnfants EntretienRemorquage Général EntretienGénéral Fonctionnement TESPEN LES Dans Fonctionnement Tracteurs des sécurité toute en l’utilisation pour ConseilsLTX19542PBA Modèle Com.poulan.www web site notre VisitezAUX Imprimé

418757, 96012008400 specifications

The Poulan 96012008400 418757 is a robust and reliable chainsaw that has garnered attention among both casual users and professional arborists. Designed primarily for cutting firewood and maintaining trees, this chainsaw is a quintessential tool for outdoor enthusiasts and homeowners alike.

One of the standout features of this model is its powerful engine. Fitted with a 20-inch bar, the chainsaw is equipped to handle larger cutting tasks with ease. The engine delivers strong performance, allowing for efficient cutting through hardwood and softwood alike, making it versatile for various applications. Furthermore, the chainsaw's lightweight design ensures that it is manageable for extended use, offering comfort during long periods of operation.

The Poulan 96012008400 418757 is designed with advanced technologies that enhance user safety and operational efficiency. It features an automatic oiler that provides constant lubrication to the chain, ensuring a smooth cutting experience while reducing wear and tear. This technology minimizes the need for manual adjustments, allowing users to focus more on their tasks. Additionally, the chain brake feature is a crucial safety element, designed to protect the user in the event of kickback, allowing for a quick stop of the chain movement.

Another impressive characteristic of the Poulan chainsaw is its easy-start system. This technology reduces the effort required to start the engine, making it accessible for all users, regardless of their experience level. The ergonomic design of the handles also contributes to user comfort, with rubber grips that absorb vibration, preventing fatigue during longer cutting sessions.

Maintenance is simplified with easy-access air filters and spark plugs, allowing users to keep their saw in top condition without the hassle of complicated disassemblies. The Poulan 96012008400 418757 also boasts a durable construction, featuring a high-quality plastic body that resists wear from environmental factors, extending the life of the equipment.

In summary, the Poulan 96012008400 418757 chainsaw combines power, safety, and user-friendly design, making it an outstanding choice for anyone in need of a reliable cutting tool. Its blend of advanced features and durability ensures that it is well-equipped to tackle a variety of cutting tasks with confidence and efficiency.
Top Page Image Contents