Poulan 96012008400, 418757 manual Transaxle Gear Shift Lever NEUTRAL- Adjustment See Fig

Page 22

SERVICE AND ADJUSTMENTS

TRANSAXLE GEAR SHIFT LEVER NEUTRAL- ADJUSTMENT (See Fig. 23)

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral (N).

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) posi- tion.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 24

TO START ENGINE WITH A WEAK BATTERY (See Fig. 25)

GEARSHIFT LEVER

NEUTRAL LOCK GATE

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

ADJUSTMENT

BOLT

FIG. 23

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 24)

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

FIG. 25

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Model PBA19542LTX Lawn TractorGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceIV. Towing Table of Contents Seat Unassembled PartsSteering Wheel KeysTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidInstall Seat See Fig Check Battery See FigCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Operate Mower See FigTo Operate on Hills Check Engine OIL Level Before Starting the EngineTo Transport ADD GasolineMowing Tips Before Each USE MaintenanceGeneral Recommendations Check Brake Operation Check Tire PressureTo Sharpen Blade See Fig TractorBlade Removal See Fig Check Operator Presence SystemEngine AIR Filter CleaningClean AIR Screen MufflerTo Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigRecheck side-to-side adjustment To Replace Mower Blade Drive Belt See Fig Belt InstallationTo Check Brake To Replace Motion Drive Belt See FigTo Adjust Steering Wheel ALIGN- Ment Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Carburetor Interlocks and RelaysFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Canada contact Outdoor Products Customer Service DeptHOP Stevens Creek Road Terry Fox Way Augusta, GA 30907 USAService Notes Suggested Guide for Sighting Slopes for Safe Operation Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Degrés Suivant LES UNE Pliez EST Ceci’ENTRETIEN Remarques Autorisé Dept Service Customer Products Outdoor Canada AuGarantie cette de exclus sont normal l’entretien et Dépannage DE Guide Conducteur le lorsqueLame de mandrin le Remplacez Tordu est lame de mandrin Un Moteur EntreposageTracteur Reglages ET Revision MoteurFig la Rossage -AVANT/CAR Roues DES ConvergenceLA DE L’ALIGNEMENT Régler Pour Voir Vitesses DE Boîte LA DE Mentge’EN Courroie LA Remplacer Pour Fig la VoirCourroie Acer Rempl Pour 18 .FIG Tondeuse DE Boîtier LE Niveler Pour19 .FIG 17 .FIGTracteur 15 .FIGAIR À Filtre Entretien’ALLUMAGE Bougie ’AIR Tamis LE NettoyerFig la Voir Lame LA Affiler Sionmistrans LA DE Moteur FluideTransmission LA DE Refroidissement Trapézoïdales CourroiesFig la Voir Lame LA Enlever EN Fonctionnement DE Système ETLubrification DE Tableau Recommandations LESGénérales Utilisation Chaque AvantTondre DE Conseils UtilisationAvec marcher le-faites moteur, le démarrez vous Quand Moteur LE Démarrer DE Avant Fonction DE Système DU Utilisation Pentes LES Dans Utiliser PourMAR EN Fonctionnement DE Système Reculer Pour ET Avancer Pour GAZ DES Commande LA Utiliser PourTeurtrac Votre Utiliser Comment Fig la Voir Arrêter PourLSW02838 ’EMBRAYAGE Tionsec la Voir Conduisant LE EN Lette MontageDesmancom des tionfonc la et PA LA DE Tracteur LE Retirer PourDesman Fig la Voir Siège LE InstallerVotre Monter Comment Com des fonction la et mentceplalemPalette LA DU Tracteur LE Sortir PourToncar Montées NON Piéces Pente-GuideProduit DE Spécifications SommaireClient DU Responsabilités CCA .MIN AMP/HREnfants EntretienRemorquage Général EntretienGénéral Fonctionnement TESPEN LES Dans Fonctionnement Tracteurs des sécurité toute en l’utilisation pour ConseilsCom.poulan.www web site notre Visitez LTX19542PBA ModèleAUX Imprimé

418757, 96012008400 specifications

The Poulan 96012008400 418757 is a robust and reliable chainsaw that has garnered attention among both casual users and professional arborists. Designed primarily for cutting firewood and maintaining trees, this chainsaw is a quintessential tool for outdoor enthusiasts and homeowners alike.

One of the standout features of this model is its powerful engine. Fitted with a 20-inch bar, the chainsaw is equipped to handle larger cutting tasks with ease. The engine delivers strong performance, allowing for efficient cutting through hardwood and softwood alike, making it versatile for various applications. Furthermore, the chainsaw's lightweight design ensures that it is manageable for extended use, offering comfort during long periods of operation.

The Poulan 96012008400 418757 is designed with advanced technologies that enhance user safety and operational efficiency. It features an automatic oiler that provides constant lubrication to the chain, ensuring a smooth cutting experience while reducing wear and tear. This technology minimizes the need for manual adjustments, allowing users to focus more on their tasks. Additionally, the chain brake feature is a crucial safety element, designed to protect the user in the event of kickback, allowing for a quick stop of the chain movement.

Another impressive characteristic of the Poulan chainsaw is its easy-start system. This technology reduces the effort required to start the engine, making it accessible for all users, regardless of their experience level. The ergonomic design of the handles also contributes to user comfort, with rubber grips that absorb vibration, preventing fatigue during longer cutting sessions.

Maintenance is simplified with easy-access air filters and spark plugs, allowing users to keep their saw in top condition without the hassle of complicated disassemblies. The Poulan 96012008400 418757 also boasts a durable construction, featuring a high-quality plastic body that resists wear from environmental factors, extending the life of the equipment.

In summary, the Poulan 96012008400 418757 chainsaw combines power, safety, and user-friendly design, making it an outstanding choice for anyone in need of a reliable cutting tool. Its blend of advanced features and durability ensures that it is well-equipped to tackle a variety of cutting tasks with confidence and efficiency.
Top Page Image Contents