Poulan 96042003401 Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1) 1/2" wrench

Utility knife

(2) 3/4" wrench

Tire pressure gauge

Pliers

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

Remove all accessible loose parts and parts cartons from carton.

Cut along dashed lines on all four panels of carton. Remove end panels and lay side panels flat.

Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

Slide extension shaft onto lower steering shaft.

Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

Position front wheels of the tractor so they are pointing straight forward.

Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

Assemble large flat washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

Snap steering wheel insert into center of steering wheel.

Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSERT

5/16 HEX BOLT

5/16 LOCK

WASHER

LARGE FLAT

WASHER

STEERING

WHEEL

STEERING BOOT

ADAPTER

TABS

TAB

SLOTS

EXTENSION SHAFT

LOWER

STEERING

SHAFT

03132

FIG. 1

6

Image 6
Contents PB19542LT General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Contents of Hardware Pack To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidInstall Seat See Figs Check Battery See FigCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Using the Reverse Operation System Reverse Operation System ROSTo Operate Mower See Fig Before Starting the Engine Mowing Tips Maintenance Lubrication ChartTractor Blade Removal See FigTo Sharpen Blade See Fig Belts BatteryEngine Transaxle CoolingCleaning Service and Adjustments To Install Mower See FigTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Replace Mower Drive Belt See Fig To Check BrakeTo Replace Motion Belt Drive See Fig To Adjust Steering Wheel ALIGN- Ment Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Wheels and Tires Tractor - Model Number PB19542LT 96042003401, Product no 42Decals KEY Part DescriptionSchematic FuseElectrical Electrical 197802Chassis 194263 Drawbar Drive Repair Parts Engine Engine Power Rating Information Steering Repair Parts Mower Deck Repair Parts Seat Mower Lift 9098 100Service Notes Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXLimited Warranty

413420, 96042003401 specifications

The Poulan 96042003401,413420 is a powerful and versatile equipment designed for both homeowners and professionals seeking high-performance tools for lawn care and maintenance. This model stands out in the market for its robust features, advanced technologies, and user-friendly characteristics.

One of the main features of the Poulan 96042003401,413420 is its efficient engine. The equipment is equipped with a reliable gas engine that provides ample power while ensuring smooth operation. This allows users to tackle various tasks such as trimming, edging, and cutting grass with ease. The engine's design emphasizes fuel efficiency, which helps users save on refueling costs over time.

In addition to its powerful engine, the Poulan 96042003401,413420 incorporates a user-friendly starting system. The easy start feature minimizes the effort required to get the machine up and running. This is particularly beneficial for users who may not be experienced with starting gas-powered equipment.

The design of the Poulan 96042003401,413420 places a strong emphasis on ergonomics. The equipment features comfortable grips that minimize strain during extended use, allowing for better maneuverability and control. This thoughtful design helps to reduce fatigue, making it easier for users to complete yard work efficiently.

The cutting technology employed in the Poulan 96042003401,413420 ensures precise and clean cuts. With an adjustable cutting height, users can customize the length of their grass to suit specific preferences or seasonal needs. This versatility makes the equipment suitable for various types of lawns and landscaping designs.

Durability is another key characteristic of the Poulan 96042003401,413420. Constructed from high-quality materials, this equipment is built to withstand the rigors of outdoor use. Users can depend on this model to perform consistently over time, even under challenging conditions.

Maintenance is simplified with this model as well. The Poulan 96042003401,413420 features easy-access components, allowing users to perform routine checks and maintenance tasks without difficulty. This ensures the longevity of the equipment and helps maintain optimal performance.

Overall, the Poulan 96042003401,413420 appeals to a wide range of users due to its powerful engine, ergonomic design, advanced cutting technology, durability, and ease of maintenance. Whether for a small garden or a larger landscape, this equipment is designed to meet various lawn care needs efficiently.