Poulan 96012004600 Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1) 1/2" wrench

Utility knife

(2) 3/4" wrench

Tire pressure gauge

Pliers

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels fl at.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large fl at washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSERT

5/16 HEX BOLT

5/16 LOCK

WASHER

LARGE FLAT

WASHER

STEERING

WHEEL

STEERING

BOOT

TABS

ADAPTER

EXTENSION

SHAFT

LOWER

STEERING

SHAFT

TAB

SLOTS

FIG. 1

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and fl at washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and fl at washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PB18542LT Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Contents of Hardware Pack To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Adjust Gauge Wheels See FigUsing the Reverse Operation System To Operate Mower See FigBefore Starting the Engine Mowing Tips Lubrication Chart MaintenanceMaintenance Schedule General RecommendationsTractor Blade Removal See FigTo Sharpen Blade See Fig Belts BatteryEngine Transaxle CoolingCleaning Service and Adjustments To Install Mower See FigTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Brake To Check BrakeTo Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

401115, 96012004600 specifications

The Poulan 96012004600,401115 is a remarkable tool designed for those who seek efficiency and power in their outdoor activities. This versatile piece of equipment is particularly well-regarded among homeowners and professionals alike who require reliable performance for yard work and landscape maintenance.

At the heart of the Poulan 96012004600,401115 is its robust engine, which delivers impressive power that allows for easy handling of various cutting tasks. Whether you're trimming grass, edging pathways, or tackling overgrown brush, this tool is equipped to handle the demands of heavy-duty yard work. The manufacturer has integrated advanced engine technologies, ensuring a balance between performance and fuel efficiency, which helps users save on running costs over time.

One of the main features of the Poulan 96012004600,401115 is its lightweight design. Weighing in at a manageable level, it allows users to maneuver the tool with ease, reducing fatigue during extended periods of use. It's an excellent choice for both casual users and professionals who require a tool that can be used for long hours without discomfort.

The ergonomic handle design is another highlight, providing users with a comfortable grip that enhances control. This feature minimizes strain on the hands and wrists, making it easier to operate the tool for prolonged durations. Additionally, the adjustable cutting height feature allows for customization according to the specific needs of the lawn or garden, making it suitable for varied terrains.

Safety is paramount in outdoor equipment, and the Poulan 96012004600,401115 does not disappoint. It comes with safety guards and easy-start mechanisms, including an automatic oiler to keep the chain properly lubricated, ensuring smooth operation and extending the tool's lifespan.

In terms of versatility, this tool can accommodate different attachments, allowing users to switch from trimming to edging to even more complex landscaping tasks with minimal effort.

Overall, the Poulan 96012004600,401115 stands out for its powerful performance, ease of use, and thoughtful features that cater to a wide range of outdoor tasks. With its combination of innovative technologies and user-friendly design, this tool is an outstanding choice for anyone looking to maintain their landscape with efficiency and precision.
Top Page Image Contents