Poulan 96012004600, 401115 manual Transaxle Gear Shift Lever NEUTRAL- Adjustment See Fig

Page 22

SERVICE AND ADJUSTMENTS

TRANSAXLE GEAR SHIFT LEVER NEUTRAL- ADJUSTMENT (See Fig. 22)

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral (N).

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) posi- tion.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

NEUTRAL

LOCK GATE

GEARSHIFT LEVER

ADJUSTMENT

BOLT

FIG. 22

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor.If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 23

TO START ENGINE WITH A WEAK BATTERY (See Fig. 24)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable fi rst from chassis and then from the fully charged battery.

•RED cable last from both batteries.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 23)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

NOTE: To seal tire punctures and prevent fl at tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

22

FIG. 24

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PB18542LT Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Contents of Hardware Pack To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Adjust Gauge Wheels See FigUsing the Reverse Operation System To Operate Mower See FigBefore Starting the Engine Mowing Tips Lubrication Chart MaintenanceMaintenance Schedule General RecommendationsBlade Removal See Fig TractorTo Sharpen Blade See Fig Belts BatteryEngine Transaxle CoolingCleaning To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Brake To Check BrakeTo Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

401115, 96012004600 specifications

The Poulan 96012004600,401115 is a remarkable tool designed for those who seek efficiency and power in their outdoor activities. This versatile piece of equipment is particularly well-regarded among homeowners and professionals alike who require reliable performance for yard work and landscape maintenance.

At the heart of the Poulan 96012004600,401115 is its robust engine, which delivers impressive power that allows for easy handling of various cutting tasks. Whether you're trimming grass, edging pathways, or tackling overgrown brush, this tool is equipped to handle the demands of heavy-duty yard work. The manufacturer has integrated advanced engine technologies, ensuring a balance between performance and fuel efficiency, which helps users save on running costs over time.

One of the main features of the Poulan 96012004600,401115 is its lightweight design. Weighing in at a manageable level, it allows users to maneuver the tool with ease, reducing fatigue during extended periods of use. It's an excellent choice for both casual users and professionals who require a tool that can be used for long hours without discomfort.

The ergonomic handle design is another highlight, providing users with a comfortable grip that enhances control. This feature minimizes strain on the hands and wrists, making it easier to operate the tool for prolonged durations. Additionally, the adjustable cutting height feature allows for customization according to the specific needs of the lawn or garden, making it suitable for varied terrains.

Safety is paramount in outdoor equipment, and the Poulan 96012004600,401115 does not disappoint. It comes with safety guards and easy-start mechanisms, including an automatic oiler to keep the chain properly lubricated, ensuring smooth operation and extending the tool's lifespan.

In terms of versatility, this tool can accommodate different attachments, allowing users to switch from trimming to edging to even more complex landscaping tasks with minimal effort.

Overall, the Poulan 96012004600,401115 stands out for its powerful performance, ease of use, and thoughtful features that cater to a wide range of outdoor tasks. With its combination of innovative technologies and user-friendly design, this tool is an outstanding choice for anyone looking to maintain their landscape with efficiency and precision.
Top Page Image Contents