Poulan 424368 Before Starting the Engine, To Operate on Hills, Towing Carts and Other Attachments

Page 11

OPERATION

TO OPERATE MOWER (See Fig. 6)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut.

•Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES (See Fig. 6)

•disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

"ENGAGED" POSITION

ATTACHMENT

LIFT LEVER HIGH POSITION

LOW

POSITION

ATTACHMENT CLUTCH LEVER "DISENGAGED" POSITION

DEFLECTOR

SHIELD

FIG. 6

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choosetheslowestspeedbeforestartingupordownhills.

•Avoid stopping or changing speed on hills.

•If stopping is absolutely necessary, push clutch/brake pedalquicklytobrakepositionandengageparkingbrake.

•Movegearshiftleverto1stgear.Besureyouhaveallowed room for tractor to roll slightly as you restart movement.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Make all turns slowly.

TOWING CARTS AND OTHER ATTACHMENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

REVERSE OPERATION SYSTEM (ROS) (See Fig. 7)

Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.

WARNING: Backing up with the attachment clutch en- gaged while mowing is strongly discouraged. Turning the ROS "ON", to allow reverse operation with the attachment clutch engaged, should only be done when the operator decides it is necessary to reposition the machine with the attachment engaged. Do not mow in reverse unless absolutely necessary.

USING THE REVERSE OPERATION SYSTEM -

•Depress clutch/brake pedal all the way down and hold.

•With engine running, turn ignition key counterclockwise to ROS "ON" position.

•Look down and behind before and while backing.

•Move gear shift lever to reverse (R) position and slowly release clutch/brake pedal to start movement.

•When use of the ROS is no longer needed, turn the ignition key clockwise to engine "ON" position.

 

 

 

 

 

 

 

 

 

 

02828

ROS "ON"

ENGINE "ON" POSITION

POSITION

(NORMAL OPERATING)

 

 

 

 

 

 

Fig. 7

TO TRANSPORT

 

 

•Raise attachment lift to highest position with attachment lift control.

•When pushing or towing your tractor, be sure gearshift lever is in neutral (N) position.

•Do not push or tow tractor at more than five (5) MPH.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

•Check engine oil with tractor on level ground.

•Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Maintenance section of this manual).

•To change engine oil, see the Maintenance section in this manual.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents PXT15538 II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Unassembled Parts Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck for Proper Position of ALL Belts Install Seat See FigCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Transport Before Starting the EngineTo Operate on Hills Towing Carts and Other AttachmentsTo Start Engine See Fig Mowing TipsADD Gasoline Powdered Graphite Type Lubricant Sparingly MaintenanceLubrication Chart Blade Removal See Fig BatteryTractor Blade CareEngine CleaningTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check BrakeFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentInterlocks and Relays To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbEngine OIL StorageOther Fuel SystemProblem Cause Correction TroubleshootingExcessive To run when operBattery will not When turningFold Along This Dotted Line Degree Slope Only Ride UP and Down Hill Not Across Hill Degrees MAXStevens Creek Road Terry Fox Way Augusta, GA 30907 USA Outdoor Products Customer Service DeptHOP Canada contactGarantie cette de exclus sont normal l’entretien et Dept Service Customer Products Outdoor Canada AuAutorisé Degrés MAX Correction Cause Problème Dépannage DE GuidePuissance de Entreposage Fig la Voir Calandre LA ET Capot LE Enlever Pour Réglages ET RévisionCarburateur LE Régler Pour Fig la Voir Tionsraparé LES Pour Roues LES Enlever Pour Fig la VoirVitesses DE Boîte LA DE Mentgechan DE Levier DU Neutre AU RéglageFig la Voir Tondeuse DE Lame DE Courroie LA Remplacer Pour Freins LES Vérifier PourFiglaVoirTONDEUSELAENLEVERPOUR Tondeuse LA Installer PourDE Boîtier LE Niveau DE Mettre Pour SedeutonMoteur EntretienPneus Fig la Voir Lame LA EnleverTrapézoïdales Courroies Lames DES EntretienMoteur de d’huile niveau le Vérifiez Utilisation Chaque AvantLubrification DE Tableau ’ESSENCE Réservoir LE Remplir UtilisationTonte DE Conseils Fig la Voir Moteur LE Démarrer PourArrière Marche EN Fonctionnement Accessoires AutresMoteur DU D’HUILE Niveau LE Vérifier Tracteur LE Transporter PourT O S I L I T U GAZ DES Commande LA Utiliser Pour02829 Ou mineures blessures des causer pourrait MoteurDu et/ou tracteur du endommagement un en ModéréesSont Courroies LES Toutes SI Vérifier MontageFrein DE Système LE Vérifier Place EN CorrectementCarton LE Deballer DE Tracteur LE Retirer AvantFig la Voir Batterie LA Vérifier Tionrecdi DE Volant LE FixerSiège Montar SIN PiezasSommaire Général Entretien EnfantsEntretien RemorquageGénéral Fonctionnement AvertissementPentes LES Dans Fonctionnement Tracteurs des sécurité toute en l’utilisation pour ConseilsPelouse DE Tracteur PXT15538

424368 specifications

The Poulan 424368 is a versatile and powerful chainsaw designed for both professionals and home users alike. Known for its reliable performance and rugged construction, this chainsaw is perfect for a variety of cutting tasks, from felling trees to pruning limbs and even light milling jobs. With several advanced features and technologies, the Poulan 424368 stands out in a competitive market.

One of the main features of the Poulan 424368 is its robust engine. It is equipped with a potent 42cc two-cycle engine that delivers impressive power, enabling users to cut through tough wood with ease. This engine is designed for optimal efficiency, ensuring that you can accomplish more with less fuel consumption. With a power output of approximately 2.8 horsepower, users can expect quick starts and consistent performance, making this chainsaw ideal for both light and heavy-duty tasks.

The chainsaw showcases a 16-inch bar, providing a perfect balance between maneuverability and cutting capacity. The length of the bar is suitable for tackling medium-sized trees and branches without compromising on the saw's agility. Additionally, the chain is designed to be low-kickback, enhancing user safety while significantly improving cutting precision.

Equipped with professional-grade features, the Poulan 424368 incorporates an easy-access air filter and a tool-free chain tensioning system. These elements contribute to simple maintenance and adjustments, allowing users to spend less time on upkeep and more time working. The primer bulb enables easy starting, reducing the frustration often associated with chainsaws.

Another notable characteristic is the ergonomic design of the Poulan 424368. It features a lightweight build with a balanced weight distribution, allowing users to operate it comfortably for extended periods. The rubberized handles provide a secure grip, ensuring that users maintain control during cutting tasks.

Safety is also a primary consideration in the design of the Poulan 424368. It includes an inertia-activated chain brake that enhances protection against accidental cuts while in operation. This feature, combined with its low vibration technology, reduces user fatigue, making it an ideal choice for extensive cutting projects.

In summary, the Poulan 424368 is a feature-rich chainsaw combining power, efficiency, and safety. With its high-performing engine, user-friendly design, and reliable safety features, it satisfies the needs of both casual users and seasoned professionals alike. Whether you are clearing debris after a storm or maintaining your landscape, the Poulan 424368 is a dependable tool that delivers exceptional results with every cut.
Top Page Image Contents