Poulan 424368 manual Service and Adjustments, To Remove Mower See Fig, To Install Mower See Fig

Page 16

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

Depress clutch/brake pedal fully and set parking brake.

Place gearshift lever in neutral position.

Place attachment clutch in “DISENGAGED” position.

Turn ignition key to “STOP” and remove key.

Make sure the blades and all moving parts have completely stopped.

Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TO REMOVE MOWER (See Fig. 14)

Mower will be easier to remove from the right side of tractor.

Place attachment clutch in “DISENGAGED” position.

Move attachment lift lever forward to lower mower to its lowest position.

Roll belt off engine pulley.

Remove small retainer spring, and remove clutch spring off pulley bolt.

Remove large retainer spring, slide collar off and push housing guide out of bracket.

Disconnect anti-swaybar from chassis bracket by re- moving retainer spring.

Disconnect suspension arms from rear deck brackets by removing retainer springs.

Disconnect front links from deck by removing retainer springs.

Raise lift lever to raise suspension arms. Slide mower out from under tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER DECK IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONT LINKS AND HOOK THE CLUTCH SPRING INTO SQUARE HOLE IN FRAME.

TO INSTALL MOWER (See Fig. 14)

Raise attachment lift lever to its highest position.

Slide mower under tractor with deflector shield to right side of tractor.

Lower lift lever to its lowest position.

Connect front links to mower deck and secure with retainer springs..

Connect suspension arms to rear deck brackets and secure with retainer springs.

Connect anti-swaybar to chassis bracket and secure with retainer spring.

Push clutch cable housing guide into bracket, slide col- lar onto guide and secure with large retainer spring.

Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring.

Make sure belt is inside the belt keeper at the idler and on both sides of the wire belt keeper as shown.

Install belt onto engine pulley.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See sides of tires for proper PSI). If tires are over or underinflated, you will not properly adjust your mower.

SMALL RETAINER SPRING

WIRE BELT KEEPER

FLAT WASHER

SUSPENSION ARMS

CLUTCH SPRING

 

BELT KEEPER

 

 

 

SQUARE HOLE

RETAINER SPRING

 

ENGINE PULLEY

ANTI-SWAY BAR

 

 

FRONT LINK

COLLAR

 

 

 

HOUSING GUIDE

 

RETAINER SPRINGS

 

 

(BOTH SIDES)

 

BRACKET

 

LARGE RETAINER SPRING

 

02845

CLUTCH SPRING

DEFLECTOR SHIELD

 

FIG. 14

16

Image 16
Contents PXT15538 Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Fig Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Operate on HillsTowing Carts and Other Attachments To TransportADD Gasoline Mowing TipsTo Start Engine See Fig Lubrication Chart MaintenancePowdered Graphite Type Lubricant Sparingly Battery TractorBlade Care Blade Removal See FigCleaning EngineService and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake Belt RemovalTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysStorage OtherFuel System Engine OILTroubleshooting Problem Cause CorrectionTo run when oper Battery will notWhen turning ExcessiveOnly Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line Degree SlopeOutdoor Products Customer Service Dept HOPCanada contact Stevens Creek Road Terry Fox Way Augusta, GA 30907 USAAutorisé Dept Service Customer Products Outdoor Canada AuGarantie cette de exclus sont normal l’entretien et Degrés MAX Dépannage DE Guide Correction Cause ProblèmePuissance de Entreposage Carburateur LE Régler Pour Réglages ET RévisionFig la Voir Calandre LA ET Capot LE Enlever Pour Fig la Voir Vitesses DE Boîte LA DE MentgechanDE Levier DU Neutre AU Réglage Fig la Voir Tionsraparé LES Pour Roues LES Enlever PourFreins LES Vérifier Pour Fig la Voir Tondeuse DE Lame DE Courroie LA Remplacer PourTondeuse LA Installer Pour DE Boîtier LE Niveau DE Mettre PourSedeuton FiglaVoirTONDEUSELAENLEVERPOUREntretien MoteurFig la Voir Lame LA Enlever Trapézoïdales CourroiesLames DES Entretien PneusLubrification DE Tableau Utilisation Chaque AvantMoteur de d’huile niveau le Vérifiez Utilisation Tonte DE ConseilsFig la Voir Moteur LE Démarrer Pour ’ESSENCE Réservoir LE RemplirAccessoires Autres Moteur DU D’HUILE Niveau LE VérifierTracteur LE Transporter Pour Arrière Marche EN FonctionnementGAZ DES Commande LA Utiliser Pour T O S I L I T U02829 Moteur Du et/ou tracteur du endommagement un enModérées Ou mineures blessures des causer pourraitMontage Frein DE Système LE VérifierPlace EN Correctement Sont Courroies LES Toutes SI VérifierDE Tracteur LE Retirer Avant Fig la Voir Batterie LA VérifierTionrecdi DE Volant LE Fixer Carton LE DeballerMontar SIN Piezas SiègeSommaire Enfants EntretienRemorquage Général EntretienAvertissement Pentes LES Dans FonctionnementTracteurs des sécurité toute en l’utilisation pour Conseils Général FonctionnementPelouse DE Tracteur PXT15538

424368 specifications

The Poulan 424368 is a versatile and powerful chainsaw designed for both professionals and home users alike. Known for its reliable performance and rugged construction, this chainsaw is perfect for a variety of cutting tasks, from felling trees to pruning limbs and even light milling jobs. With several advanced features and technologies, the Poulan 424368 stands out in a competitive market.

One of the main features of the Poulan 424368 is its robust engine. It is equipped with a potent 42cc two-cycle engine that delivers impressive power, enabling users to cut through tough wood with ease. This engine is designed for optimal efficiency, ensuring that you can accomplish more with less fuel consumption. With a power output of approximately 2.8 horsepower, users can expect quick starts and consistent performance, making this chainsaw ideal for both light and heavy-duty tasks.

The chainsaw showcases a 16-inch bar, providing a perfect balance between maneuverability and cutting capacity. The length of the bar is suitable for tackling medium-sized trees and branches without compromising on the saw's agility. Additionally, the chain is designed to be low-kickback, enhancing user safety while significantly improving cutting precision.

Equipped with professional-grade features, the Poulan 424368 incorporates an easy-access air filter and a tool-free chain tensioning system. These elements contribute to simple maintenance and adjustments, allowing users to spend less time on upkeep and more time working. The primer bulb enables easy starting, reducing the frustration often associated with chainsaws.

Another notable characteristic is the ergonomic design of the Poulan 424368. It features a lightweight build with a balanced weight distribution, allowing users to operate it comfortably for extended periods. The rubberized handles provide a secure grip, ensuring that users maintain control during cutting tasks.

Safety is also a primary consideration in the design of the Poulan 424368. It includes an inertia-activated chain brake that enhances protection against accidental cuts while in operation. This feature, combined with its low vibration technology, reduces user fatigue, making it an ideal choice for extensive cutting projects.

In summary, the Poulan 424368 is a feature-rich chainsaw combining power, efficiency, and safety. With its high-performing engine, user-friendly design, and reliable safety features, it satisfies the needs of both casual users and seasoned professionals alike. Whether you are clearing debris after a storm or maintaining your landscape, the Poulan 424368 is a dependable tool that delivers exceptional results with every cut.