Poulan 424368 manual To Adjust Steering Wheel Alignment, Front Wheel TOE-IN/CAMBER

Page 18

SERVICE AND ADJUSTMENTS

TOREPLACEMOTIONDRIVEBELT(SeeFig.20)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Remove belt from stationary idler and clutching idler.

•Remove belt downward from around engine pulley.

•Pull belt slack toward rear of tractor. Remove belt up- wards from transaxle pulley by deflecting belt keepers.

•Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

•Carefully work new belt down between transaxle belt keepers and onto the input pulley.

•Slide belt into the center span keeper.

•Pull belt toward front of tractor and roll around the top groove of engine pulley.

•Install belt through stationary idler and clutching idler.

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this section of manual).

ENGINE PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

CENTER SPAN

KEEPER

TRANSAXLE

PULLEY

FIG. 20

TRANSAXLE GEAR SHIFT LEVER NEUTRAL ADJUSTMENT (See Fig. 21)

The transaxle should be in neutral when the gear shift lever is in neutral (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral.

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

GEARSHIFT

NEUTRAL

LEVER

LOCK

 

GATE

 

ADJUSTMENT

 

BOLT

FIG. 21

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL (See Fig. 22)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

AXLE

RETAINING WASHERS

RING

COVER

 

SQUARE KEY (REAR WHEEL ONLY)

FIG. 22

TO START ENGINE WITH A WEAK BATTERY (See Fig. 23)

WARNING: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents PXT15538 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Deck Levelness Install Seat See FigCheck Tire Pressure Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Towing Carts and Other Attachments Before Starting the EngineTo Operate on Hills To TransportMowing Tips ADD GasolineTo Start Engine See Fig Maintenance Lubrication ChartPowdered Graphite Type Lubricant Sparingly Blade Care BatteryTractor Blade Removal See FigCleaning EngineTo Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigTo Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Carburetor Interlocks and RelaysFuel System StorageOther Engine OILTroubleshooting Problem Cause CorrectionWhen turning To run when operBattery will not ExcessiveOnly Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line Degree SlopeCanada contact Outdoor Products Customer Service DeptHOP Stevens Creek Road Terry Fox Way Augusta, GA 30907 USADept Service Customer Products Outdoor Canada Au AutoriséGarantie cette de exclus sont normal l’entretien et Degrés MAX Dépannage DE Guide Correction Cause ProblèmePuissance de Entreposage Réglages ET Révision Carburateur LE Régler PourFig la Voir Calandre LA ET Capot LE Enlever Pour DE Levier DU Neutre AU Réglage Fig la VoirVitesses DE Boîte LA DE Mentgechan Fig la Voir Tionsraparé LES Pour Roues LES Enlever PourFreins LES Vérifier Pour Fig la Voir Tondeuse DE Lame DE Courroie LA Remplacer PourSedeuton Tondeuse LA Installer PourDE Boîtier LE Niveau DE Mettre Pour FiglaVoirTONDEUSELAENLEVERPOUREntretien MoteurLames DES Entretien Fig la Voir Lame LA EnleverTrapézoïdales Courroies PneusUtilisation Chaque Avant Lubrification DE TableauMoteur de d’huile niveau le Vérifiez Fig la Voir Moteur LE Démarrer Pour UtilisationTonte DE Conseils ’ESSENCE Réservoir LE RemplirTracteur LE Transporter Pour Accessoires AutresMoteur DU D’HUILE Niveau LE Vérifier Arrière Marche EN FonctionnementGAZ DES Commande LA Utiliser Pour T O S I L I T U02829 Modérées MoteurDu et/ou tracteur du endommagement un en Ou mineures blessures des causer pourraitPlace EN Correctement MontageFrein DE Système LE Vérifier Sont Courroies LES Toutes SI VérifierTionrecdi DE Volant LE Fixer DE Tracteur LE Retirer AvantFig la Voir Batterie LA Vérifier Carton LE DeballerMontar SIN Piezas SiègeSommaire Remorquage EnfantsEntretien Général EntretienTracteurs des sécurité toute en l’utilisation pour Conseils AvertissementPentes LES Dans Fonctionnement Général FonctionnementPelouse DE Tracteur PXT15538

424368 specifications

The Poulan 424368 is a versatile and powerful chainsaw designed for both professionals and home users alike. Known for its reliable performance and rugged construction, this chainsaw is perfect for a variety of cutting tasks, from felling trees to pruning limbs and even light milling jobs. With several advanced features and technologies, the Poulan 424368 stands out in a competitive market.

One of the main features of the Poulan 424368 is its robust engine. It is equipped with a potent 42cc two-cycle engine that delivers impressive power, enabling users to cut through tough wood with ease. This engine is designed for optimal efficiency, ensuring that you can accomplish more with less fuel consumption. With a power output of approximately 2.8 horsepower, users can expect quick starts and consistent performance, making this chainsaw ideal for both light and heavy-duty tasks.

The chainsaw showcases a 16-inch bar, providing a perfect balance between maneuverability and cutting capacity. The length of the bar is suitable for tackling medium-sized trees and branches without compromising on the saw's agility. Additionally, the chain is designed to be low-kickback, enhancing user safety while significantly improving cutting precision.

Equipped with professional-grade features, the Poulan 424368 incorporates an easy-access air filter and a tool-free chain tensioning system. These elements contribute to simple maintenance and adjustments, allowing users to spend less time on upkeep and more time working. The primer bulb enables easy starting, reducing the frustration often associated with chainsaws.

Another notable characteristic is the ergonomic design of the Poulan 424368. It features a lightweight build with a balanced weight distribution, allowing users to operate it comfortably for extended periods. The rubberized handles provide a secure grip, ensuring that users maintain control during cutting tasks.

Safety is also a primary consideration in the design of the Poulan 424368. It includes an inertia-activated chain brake that enhances protection against accidental cuts while in operation. This feature, combined with its low vibration technology, reduces user fatigue, making it an ideal choice for extensive cutting projects.

In summary, the Poulan 424368 is a feature-rich chainsaw combining power, efficiency, and safety. With its high-performing engine, user-friendly design, and reliable safety features, it satisfies the needs of both casual users and seasoned professionals alike. Whether you are clearing debris after a storm or maintaining your landscape, the Poulan 424368 is a dependable tool that delivers exceptional results with every cut.
Top Page Image Contents