Poulan 401487 manual Before Starting the Engine, Check Engine OIL Level, ADD Gasoline

Page 13

OPERATION

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already fi lled with summer weight oil.

•Check engine oil with tractor on level ground.

•Remove oil fi ll cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfi ll.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Maintenance section of this manual).

•To change engine oil, see the Maintenance section in this manual.

ADD GASOLINE

•Fill fuel tank to bottom of fi ller neck. Do not overfi ll. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can at- tract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 5)

When starting the engine for the fi rst time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

•Place gear shift lever in neutral (N) position.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to choke () position.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to“START” position and release key as soon as engine starts. Do not run starter continuously for more than fi fteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke ( ) position and retry.

WARM WEATHER STARTING (50° F and above)

•When engine starts, move the throttle control to the fast position.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING ( 50° F and below)

•When engine starts, allow engine to run with the throttle control in the choke () position until the engine runs roughly, then move throttle control to fast position.This may require an engine warm-up period from several seconds to several minutes, depending on the tem- perature.

•The attachments can also be used during the engine warm-up period.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Always Wear EYE Protection During Operation ModelSafe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Contents of Hardware Pack Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Reverse Operation System ROSTo Operate on Hills To TransportCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMowing Tips General Recommendations MaintenanceBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine BatteryBelts Transaxle CoolingClean AIR Screen CleaningAIR Filter MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Belt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake To Check and Adjust Brake See FigTo Replace Motion Drive Belt See Fig To Check BrakeTo Adjust Steering Wheel ALIGN- Ment Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

401487 specifications

The Poulan 401487 is a powerful and versatile chainsaw designed for both professional arborists and home users. Known for its robust performance, it is ideal for cutting firewood, clearing brush, and felling small to medium-sized trees. This chainsaw is equipped with a range of features that enhance its functionality and ensure user comfort during operation.

One of the standout features of the Poulan 401487 is its potent engine. Powered by a reliable 40cc two-stroke engine, it offers a balance of performance and efficiency, allowing users to tackle a variety of tasks with ease. The engine is designed to start quickly and run smoothly, even under heavy loads. The impressive power output ensures that users can trim branches or cut logs swiftly.

The chainsaw comes with a 16-inch cutting bar, which strikes an excellent balance between maneuverability and cutting capacity. This length is suitable for handling most domestic woodcutting jobs, making it a popular choice among homeowners. The low kickback chain also enhances safety while ensuring effective cutting performance.

In terms of technology, the Poulan 401487 features an automatic oiling system that keeps the chain lubricated during use. This not only extends the life of the chain and bar but also allows for continuous operation without frequent maintenance interruptions. The easy-access air filter provides straightforward maintenance, ensuring the chainsaw remains in optimal condition, which is vital for longevity.

User comfort is another priority for the Poulan 401487. It incorporates a comfortable handle with anti-vibration technology, reducing fatigue during extended use. This feature is especially beneficial for professional users who work for long hours, as it helps maintain control and minimizes strain on the hands and arms.

The construction of the Poulan 401487 is robust yet lightweight, making it easy to handle without sacrificing durability. This design facilitates better maneuverability, allowing users to navigate tight spaces with ease. Additionally, the chainsaw features a safety brake that engages immediately if the kickback occurs, providing an essential layer of protection for the operator.

Overall, the Poulan 401487 stands out as a reliable and efficient chainsaw, equipped with features that cater to both performance and safety. Whether for occasional yard work or regular professional use, it delivers consistent results, making it an excellent choice for anyone in need of a dependable cutting tool.
Top Page Image Contents