Poulan 401487 manual Storage, Other, Fuel System, Engine OIL, Cylinders

Page 24

STORAGE

Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more.

WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

•Clean entire tractor (See “CLEANING” in the Mainte- nance section of this manual).

•Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

•Lubricate as shown in the Maintenance section of this manual.

•Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

•Touch up all rusted or chipped paint surfaces; sand lightly before painting.

BATTERY

•Fully charge the battery for storage.

•After a period of time in storage, battery may require recharging.

•To help prevent corrosion and power leakage during long periods of storage, battery cables should be dis- connected and battery cleaned thoroughly (see “TO CLEAN BATTERY AND TERMINALS” in the Mainte- nance section of this manual).

•After cleaning, leave cables disconnected and place cables where they cannot come in contact with battery terminals.

•If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANTTO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTUREWHICH LEADSTO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

•Empty the fuel tank by starting the engine and let it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in mini- mizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER(S)

•Remove spark plug(s).

•Pour one ounce of oil through spark plug hole(s) into cylinder(s).

•Turn ignition key to “START” position for a few seconds to distribute oil.

•Replace with new spark plug(s).

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your tractor indoors and cover it to give protection from dust and dirt.

•Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust.

IMPORTANT: NEVER COVERTRACTORWHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Model Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Contents of Hardware Pack Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Operate Mower See FigTo Operate on Hills To TransportBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Maintenance General RecommendationsTractor Blade Removal See FigTo Sharpen Blade See Fig Battery EngineBelts Transaxle CoolingCleaning Clean AIR ScreenAIR Filter MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Check and Adjust Brake See Fig To Adjust BrakeTo Replace Motion Drive Belt See Fig To Check BrakeTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

401487 specifications

The Poulan 401487 is a powerful and versatile chainsaw designed for both professional arborists and home users. Known for its robust performance, it is ideal for cutting firewood, clearing brush, and felling small to medium-sized trees. This chainsaw is equipped with a range of features that enhance its functionality and ensure user comfort during operation.

One of the standout features of the Poulan 401487 is its potent engine. Powered by a reliable 40cc two-stroke engine, it offers a balance of performance and efficiency, allowing users to tackle a variety of tasks with ease. The engine is designed to start quickly and run smoothly, even under heavy loads. The impressive power output ensures that users can trim branches or cut logs swiftly.

The chainsaw comes with a 16-inch cutting bar, which strikes an excellent balance between maneuverability and cutting capacity. This length is suitable for handling most domestic woodcutting jobs, making it a popular choice among homeowners. The low kickback chain also enhances safety while ensuring effective cutting performance.

In terms of technology, the Poulan 401487 features an automatic oiling system that keeps the chain lubricated during use. This not only extends the life of the chain and bar but also allows for continuous operation without frequent maintenance interruptions. The easy-access air filter provides straightforward maintenance, ensuring the chainsaw remains in optimal condition, which is vital for longevity.

User comfort is another priority for the Poulan 401487. It incorporates a comfortable handle with anti-vibration technology, reducing fatigue during extended use. This feature is especially beneficial for professional users who work for long hours, as it helps maintain control and minimizes strain on the hands and arms.

The construction of the Poulan 401487 is robust yet lightweight, making it easy to handle without sacrificing durability. This design facilitates better maneuverability, allowing users to navigate tight spaces with ease. Additionally, the chainsaw features a safety brake that engages immediately if the kickback occurs, providing an essential layer of protection for the operator.

Overall, the Poulan 401487 stands out as a reliable and efficient chainsaw, equipped with features that cater to both performance and safety. Whether for occasional yard work or regular professional use, it delivers consistent results, making it an excellent choice for anyone in need of a dependable cutting tool.
Top Page Image Contents