Poulan 401487 manual Tractor, Blade Removal See Fig, To Sharpen Blade See Fig

Page 16

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than fi ve (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See“PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent fl at tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OP- ERATION SYSTEM (ROS)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

•When the engine is running, any attempt by the operator to leave the seat without fi rst setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch en- gaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

ROS "ON" POSITION

ENGINE "ON" POSITION

 

(NORMAL OPERATING)

828

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 8)

•Raise mower to highest position to allow access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

•Remove blade bolt by turning counterclockwise.

•Install new or resharpened blade with stamped "THIS SIDE UP" facing deck and mandrel assembly.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED.

BLADE

STAR

 

 

CENTER

 

 

HOLE

 

BLADE BOLT

 

 

(SPECIAL)

02544

 

 

MANDREL

 

 

 

 

ASSEMBLY

FIG. 8

TO SHARPEN BLADE (See Fig. 9)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An un- balanced blade will cause excessive vibration and eventual damage to mower and engine.

•The blade can be sharpened with a fi le or on a grind- ing wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Contents of Hardware Pack Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Operate Mower See FigTo Operate on Hills To TransportBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Maintenance General RecommendationsBlade Removal See Fig TractorTo Sharpen Blade See Fig Battery EngineBelts Transaxle CoolingCleaning Clean AIR ScreenAIR Filter MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Check and Adjust Brake See Fig To Adjust BrakeTo Replace Motion Drive Belt See Fig To Check BrakeTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

401487 specifications

The Poulan 401487 is a powerful and versatile chainsaw designed for both professional arborists and home users. Known for its robust performance, it is ideal for cutting firewood, clearing brush, and felling small to medium-sized trees. This chainsaw is equipped with a range of features that enhance its functionality and ensure user comfort during operation.

One of the standout features of the Poulan 401487 is its potent engine. Powered by a reliable 40cc two-stroke engine, it offers a balance of performance and efficiency, allowing users to tackle a variety of tasks with ease. The engine is designed to start quickly and run smoothly, even under heavy loads. The impressive power output ensures that users can trim branches or cut logs swiftly.

The chainsaw comes with a 16-inch cutting bar, which strikes an excellent balance between maneuverability and cutting capacity. This length is suitable for handling most domestic woodcutting jobs, making it a popular choice among homeowners. The low kickback chain also enhances safety while ensuring effective cutting performance.

In terms of technology, the Poulan 401487 features an automatic oiling system that keeps the chain lubricated during use. This not only extends the life of the chain and bar but also allows for continuous operation without frequent maintenance interruptions. The easy-access air filter provides straightforward maintenance, ensuring the chainsaw remains in optimal condition, which is vital for longevity.

User comfort is another priority for the Poulan 401487. It incorporates a comfortable handle with anti-vibration technology, reducing fatigue during extended use. This feature is especially beneficial for professional users who work for long hours, as it helps maintain control and minimizes strain on the hands and arms.

The construction of the Poulan 401487 is robust yet lightweight, making it easy to handle without sacrificing durability. This design facilitates better maneuverability, allowing users to navigate tight spaces with ease. Additionally, the chainsaw features a safety brake that engages immediately if the kickback occurs, providing an essential layer of protection for the operator.

Overall, the Poulan 401487 stands out as a reliable and efficient chainsaw, equipped with features that cater to both performance and safety. Whether for occasional yard work or regular professional use, it delivers consistent results, making it an excellent choice for anyone in need of a dependable cutting tool.
Top Page Image Contents