Poulan 401487 Transaxle Gear Shift Lever NEUTRAL- Adjustment See Fig, Front Wheel TOE-IN/CAMBER

Page 22

SERVICE AND ADJUSTMENTS

TRANSAXLE GEAR SHIFT LEVER NEUTRAL- ADJUSTMENT (See Fig. 21)

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral (N).

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) posi- tion.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

NEUTRAL

LOCK GATE

GEARSHIFT LEVER

ADJUSTMENT

BOLT

FIG. 21

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor.If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 22)

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 22

TO START ENGINE WITH A WEAK BATTERY (See Fig. 23)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable fi rst from chassis and then from the fully charged battery.

•RED cable last from both batteries.

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

NOTE: To seal tire punctures and prevent fl at tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

FIG. 23

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Model Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Contents of Hardware Pack To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Reverse Operation System ROSTo Operate Mower See Fig To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Maintenance General RecommendationsBlade Removal See Fig TractorTo Sharpen Blade See Fig Belts BatteryEngine Transaxle CoolingAIR Filter CleaningClean AIR Screen MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Brake To Check BrakeTo Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

401487 specifications

The Poulan 401487 is a powerful and versatile chainsaw designed for both professional arborists and home users. Known for its robust performance, it is ideal for cutting firewood, clearing brush, and felling small to medium-sized trees. This chainsaw is equipped with a range of features that enhance its functionality and ensure user comfort during operation.

One of the standout features of the Poulan 401487 is its potent engine. Powered by a reliable 40cc two-stroke engine, it offers a balance of performance and efficiency, allowing users to tackle a variety of tasks with ease. The engine is designed to start quickly and run smoothly, even under heavy loads. The impressive power output ensures that users can trim branches or cut logs swiftly.

The chainsaw comes with a 16-inch cutting bar, which strikes an excellent balance between maneuverability and cutting capacity. This length is suitable for handling most domestic woodcutting jobs, making it a popular choice among homeowners. The low kickback chain also enhances safety while ensuring effective cutting performance.

In terms of technology, the Poulan 401487 features an automatic oiling system that keeps the chain lubricated during use. This not only extends the life of the chain and bar but also allows for continuous operation without frequent maintenance interruptions. The easy-access air filter provides straightforward maintenance, ensuring the chainsaw remains in optimal condition, which is vital for longevity.

User comfort is another priority for the Poulan 401487. It incorporates a comfortable handle with anti-vibration technology, reducing fatigue during extended use. This feature is especially beneficial for professional users who work for long hours, as it helps maintain control and minimizes strain on the hands and arms.

The construction of the Poulan 401487 is robust yet lightweight, making it easy to handle without sacrificing durability. This design facilitates better maneuverability, allowing users to navigate tight spaces with ease. Additionally, the chainsaw features a safety brake that engages immediately if the kickback occurs, providing an essential layer of protection for the operator.

Overall, the Poulan 401487 stands out as a reliable and efficient chainsaw, equipped with features that cater to both performance and safety. Whether for occasional yard work or regular professional use, it delivers consistent results, making it an excellent choice for anyone in need of a dependable cutting tool.
Top Page Image Contents