Poulan 193747 manual Lawn Mower, Tires, Blade Care

Page 19
Read the maintenance section of your engine manual.
LUBRICATION
Change the oil after the first two hours of oper- ation and every 25 hours thereafter or at least once a year if the lawn mower is not used for
25 hours in one year. Refer to engine manual.
19
Grass catcher may be hosed with water but must be dry when used.
CAUTION: Under normal usage, the catcher material is subject to deterioration and wear and should therefore be checked to ensure compliance with original manufacturer specifications.
ENGINE

LAWN MOWER

Always observe safety rules when perform- ing any maintenance.

TIRES

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may

cause tire damage.

BLADE CARE

For best results, mower blade must be kept sharp. Replace a bent or damaged blade. CAUTION: Use only a replacement blade approved by the manufacturer of your mower. Using a blade not approved by the manu- facturer of your mower is hazardous, could damage your mower and void your warranty.

TO REMOVE BLADE

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

•Turn lawn mower on its side. Make sure air filter and carburetor are up.

•Use a wood block between blade and mower housing to prevent blade from turning when removing blade bolt.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

•Remove blade bolt by turning counter- clockwise.

•Remove blade and attaching hardware (bolt, lock washer, hardened washer).

NOTE: Remove the blade adapter and check the key inside hub of blade adapter. The key must be in good condition to work properly. Replace adapter if damaged.

TO REPLACE BLADE

•Turn lawn mower on it’s side. See engine manual for proper direction of turning over the engine.

•Use a wood block between blade and mower housing to prevent blade from turning when removing blade bolt.

•Protect your hands with gloves and/or wrap blade with heavy cloth.

•Removebladebolt,lockwasher,flatwasher.

•Remove blade and blade adapter.

•Inspect the key inside blade adapter. Replace adapter if damaged.

IMPORTANT: Blade bolt is Grade 8 heat treated.

•Install new or sharpened blade with trailing edge up toward the engine.

•Position blade on blade adapter. Align the two (2) holes in blade with raised lugs of adapter.

•Reassemble blade bolt, lock washer and flat washer into blade adapter and crankshaft in exact order as shown.

•Position block of wood between blade and mower housing.

•Tighten blade bolt securely. Recom- mended tightening torque is 35-40 ft. lbs.

IMPORTANT: Blade bolt is heat treated. If bolt needs replacing, replace only with approved bolt shown in the Repair Parts section of this manual.

Blade adapter

Key

Crankshaft

 

 

keyway

Lockwasher

 

 

Blade

 

 

Blade

 

 

bolt Hardened

Trailing edge

Crankshaft

washer

TO SHARPEN BLADE

NOTE: We do not recommend sharpening the blade - but if you do, be sure the blade is balanced. An unbalanced blade will cause excessive vibration and eventual damage to lawn mower and engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, drive a nail into a beam or wall. Leave about one inch of the straight nail exposed. Place center hole of blade over the head of the nail. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the

heavy end until the blade is balanced.

GRASS CATCHER (IF SO EQUIPPED)

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Economy Push Rotary Safety Rules Table of ContentsDo not General Service III. ChildrenII. Slope Operation IV. Safe Handling of GasolineEngines To Remove Mower from CartonBriggs & Stratton Engines Tecumseh HondaParts Packed Separately in Carton Parts BAG Contents Group C Group E USE Hardware Group a AssemblyAssemble Lower Handle Assemble Upper HandleAssemble Wheels Assemble Upstop BracketInstall Control BAR Install Discharge GuardModels with Briggs & Stratton Quantum Engines USE Hardware Group EAssemble Engine Zone Control Cable to Engine Briggs & Stratton Classic and Sprint EnginesModels with Briggs & Stratton Classic or Sprint Engine Assemble Engine Zone Control Cable to EngineModels with Tecumseh Engine Assemble Grass Catcher SparkplugbootifequippedAssemble Cables to Upper Handle Assemble Rope GuideOperation HOW to USE Your Lawn MowerTo Adjust Cutting Height Models with Manual Adjust BOLT-ON WheelsFill Engine with OIL Operator Presence Engine Control BARGrass Catcher Rear Discharge Models only Before Starting EngineMowing Tips To Start EngineBefore Each USE MaintenanceLubrication Chart General RecommendationsTires Lawn MowerBlade Care Engine Service and AdjustmentsLawn Mower Engine StorageOther Does not start Problem Cause CorrectionStarter rope

193747 specifications

The Poulan 193747 is a powerful and efficient chainsaw that is designed for both professional and residential use. Known for its durability and high performance, this chainsaw is a popular choice among homeowners and landscapers alike.

One of the main features of the Poulan 193747 is its robust engine, which delivers reliable power for various cutting tasks. The chainsaw is equipped with a high-performance 50cc two-stroke engine, providing an ideal balance between power and weight. This ensures that users can handle the chainsaw for extended periods without undue fatigue.

Another standout characteristic of the Poulan 193747 is its lightweight design. Weighing in at just around 10 pounds, this chainsaw is easy to maneuver, making it suitable for overhead cuts and reaching into tight spaces. The ergonomic handle provides a comfortable grip, reducing vibrations and enhancing control during operation.

The chainsaw features a 20-inch bar and chain, allowing for effective cutting of larger trees and limbs. With a chain speed of up to 15 meters per second, it enhances cutting efficiency, making tasks quicker and reducing overall fatigue. Additionally, the tool-less chain tensioning system allows users to adjust and maintain chain tension easily without the need for additional tools.

In terms of technology, the Poulan 193747 incorporates advanced air induction technology. This system helps to keep debris out of the air filter, resulting in improved engine performance and prolonged filter life. The easy-start system minimizes the effort required to start the chainsaw, ensuring a hassle-free experience even for those who are less experienced.

Safety is also a top priority in the design of the Poulan 193747. The chainsaw is equipped with a handguard and a chain brake that automatically engages during kickback situations. These features help protect the user from accidents and injuries, making it a reliable choice for both novice and experienced operators.

Overall, the Poulan 193747 combines power, portability, and safety features in a versatile chainsaw that can handle various cutting tasks. Whether you're pruning trees, cutting firewood, or clearing debris, the Poulan 193747 proves to be an excellent tool, blending performance with user-friendly design for effective outdoor work.
Top Page Image Contents