HHB comm CDR 830 manuel dutilisation Display messages relating to recording

Page 41

7 Additional information

Display messages relating to recording

Note: In the table below, ** indicates a track number.

Display

Cause

Remedy

 

 

 

 

 

Can't

This appears when the

Record the source manually, or record through the

 

SYNC

SYNCHRO button is pressed

analog input.

 

 

when the input selector is set

 

 

 

to a digital input, and the

 

 

 

source selected is not

 

 

 

recognized as CD, MD, DCC,

 

 

 

or DAT.

 

 

 

 

 

 

DIN

The digital source was

Check that the digital input cable is connected properly

 

UNLOCK

interrupted.

and that the power of the source player is on.

 

 

The source is not audio, or is

Check that the source is a regular music source.

 

 

an incompatible format (e.g.

 

 

 

a CD-ROM).

 

 

 

 

 

 

CHECK

The source player was

Stop the source player. After a short time, SYNC–1 or

 

INPUT?

already playing when the

SYNC–ALL is displayed, and the recorder goes into

 

 

SYNCHRO button was

synchro–record-pause mode.

 

 

pressed.

 

 

 

 

 

 

** SET UP

The unit is preparing to

Wait until the message disappears.

 

 

record.

 

 

 

 

 

 

REPAIR

The recorder was switched

While REPAIR is displayed, the recorder automatically

 

 

off/unplugged after

examines the recorded area of the disc and updates the

 

 

recording without ejecting

track numbers and recording time data. This process

 

 

the disc. The recorder could

takes about 40 minutes for a fully recorded disc.

 

 

not write essential recording

Finalization or further recording is possible once the

 

 

information onto the disc.

REPAIR message disappears.

 

 

 

 

 

 

 

 

REC FULL

No more recording is

Use another disc, or erase the CD-RW disc.

 

 

possible because the

 

 

 

available recording time of

 

 

 

the disc has been used up, or

 

 

 

99 tracks have already been

 

 

 

recorded on the disc.

 

 

 

 

 

 

If digital synchro-recording fails to operate correctly, check the following:

1.Pause playback of the source, then press the DIGITAL SYNCHRO button again.

•If you’re recording from a portable CD player, etc., make sure that the shock-protection feature is switched off.

2.Start playback of the source component once you see the SYNCHRO indicator start to blink.

3.If none of the above solves the problem, use manual digital recording to record.

•Digital synchro-recording uses a digital sub-signal contained in the source player’s digital output. Digital synchro-recording will not work when recording from the following devices:

•CD players whose digital output does not include a sub-signal

•Portable CD, MD or DVD players which do not output a digital signal when stopped.

41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Operating Instructions Important Safety Instructions For U.S. model Class Laser Product Contents Hints on installation Features of the CDR-830 BurnIT CD recorderUsing this manual Care and maintenance Putting the batteries in the remote controlAbout CD, CD-R and CD-RW discs Recording copyright material Recording and finalizing discsUsing the digital inputs Connecting up for digital playback & recordingUsing the digital outputs About optical and coaxial jacksPOWER-CORD Caution Connecting up for analog playback & recordingFront panel Remote Display Switching on for the first time Features Using the menuSelecting tracks DirectlyDigital recording restrictions Showing disc informationIntroduction to CD recording Power interruptions Digital signal interruptionsRecording modes Miscellaneous informationSynchro Recording one track from a sourcePress 7 to finish recording Recording all tracks from a sourceAutomatically recording and finalizing a disc Start playing the source to check the signal Press Record REC on the remote controlWhen youre done, press Manual recordingMake sure one of the digital inputs is selected Setting the digital recording levelPress Input Selector to choose the analog input Setting the analog recording levelAdjust the balance using the REC Balance buttons Setting the balanceEnter Press the jog dial Enter to confirm the balanceFinalizing a disc Resetting the recorderLoad the CD-R or CD-RW you want to finalize Press FinalizeClearing the playlist Programming the track orderClearing a track from the playlist Checking whats in the playlistRepeating tracks Playing tracks at randomFading in and fading out Playing a disc with skip IDsSkipping Setting skip IDsUnwanted tracks Clearing skip IDsPress Text Using CD textLoad the CD-R or CD-RW you wish to edit Press Text Editing CD textEdit the text Eject or finalize the discCopying track names to other tracks Press Text to leave the track name modeGo to the track with the name you want to copy Press Name Clip againDelete Automatically numbering tracksManually numbering tracks Starting tracks in time increments Setting the fade lengthRecording fade ins and fade outs Recording a fade¥ REC Mute Recording blank sectionsChecking whats at the end of a disc Monitoring a source To establish the copy-bit Scms settingErasing a CD- RW disc When a non-finalized disc is loadedPress Erase Press 8 6 on the front panel to start erasingPress and hold Erase for about four seconds When a finalized disc is loadedReinitializing a disc Understanding display messages Display messages relating to playback TroubleshootingDisplay messages relating to recording Turned on Power cannot beNo sound is heard During playbackGeneral SpecificationsTNGZF/00J00001 Printed PRB1312-A Quick Reference Guide BurnIT CDR830 Compact Disc Recorder Operating Instructions Supplement Supplement Technical Data
Top Page Image Contents