Poulan 190785 manual Tractor, Brake Operation, Tires, Operator Presence System, Blade Care

Page 15

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 8)

•Raise mower to highest position to allow access to blades.

•Remove blade bolt, lock washer and flat washer securing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble blade bolt, lock washer and flat washer in exact order as shown.

•Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS HEATTREATED.IF BOLT NEEDS REPLACING, REPLACE ONLY WITH APPROVE BOLT SHOWN IN THE REPAIR PARTS.

MANDREL

TRAILINGASSEMBLY EDGE UP

CENTER

HOLE

LOCK WASHER

STAR

FLAT WASHER

BLADE

 

BLADE BOLT

FIG. 8

TO SHARPEN BLADE (See Fig. 9)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An un- balanced blade will cause excessive vibration and eventual damage to mower and engine.

•The blade can be sharpened with a file or on a grind- ing wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

CENTER HOLE

5/8" BOLT

BLADE

OR PIN

 

FIG. 9

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model NO. PO15538B II. Slope Operation Safety RulesIV. Service General OperationSafety Rules Table of Contents Steering Wheel Seat Unassembled PartsBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonHOW to SET UP Your Tractor Install Seat See FigCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Start Engine See Fig Mowing TipsBefore Each USE MaintenanceLubrication Chart General RecommendationsOperator Presence System TractorBrake Operation TiresTransaxle Cooling BatteryEngine BeltsMuffler CleaningClean AIR Screen AIR FilterService and Adjustments To Install Mower See FigTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Adjust Steering Wheel ALIGN- Ment To Replace Motion Drive Belt See FigTo Replace Fuse Replacing Battery See FigsTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable To Adjust Choke ControlEngine OIL StorageOther Fuel SystemTroubleshooting Points With attachment clutch Tractor - Model Number PO15538B SchematicElectrical KEY Part Description Chassis 174643X014 Drive KEY Part NO. NO. Description Steering KEY Part Description Spark Arrester Engine Optional EquipmentSeatlt.bolt1 SeatWheels & Tires Decals188822 Mower LiftMower Deck Repair Parts Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

190785 specifications

The Poulan 190785 is a powerful and versatile chainsaw designed for both professional and residential forestry tasks. This model is particularly noted for its reliability and efficiency, making it a popular choice among users who require a robust tool for cutting, pruning, and tree removal.

One of the standout features of the Poulan 190785 is its powerful engine. It typically comes equipped with a 2-cycle gas engine that delivers impressive horsepower, ensuring that users can tackle even the toughest jobs with ease. The engine design focuses on minimizing fuel consumption while maximizing power, which allows for longer operational periods before needing to refuel.

The chainsaw features a 18-inch bar and chain, providing an optimal cutting length for a variety of applications, from trimming branches to felling small to medium-sized trees. The chain speed is notably high, which enhances cutting efficiency and reduces the physical effort needed by the operator. Additionally, the bar is designed with a low kickback feature, enhancing safety during use.

In terms of usability, the Poulan 190785 incorporates several ergonomic designs. The comfortable handle is designed for better grip and control, reducing user fatigue during extended operation. The chainsaw also includes an automatic oiling system, which ensures that the chain operates smoothly, reducing wear and extending the tool's lifespan.

Safety is a priority with the Poulan 190785, which includes features such as a chain brake that immediately stops the chain in case of kickback, protecting the operator from potential injuries. The chainsaw’s lightweight construction further enhances its maneuverability, allowing users to easily navigate around their work environment.

Maintenance is made simpler with the Poulan 190785 due to its easy-access air filter and carburetor, facilitating routine checks and cleaning. This design consideration ensures that the chainsaw remains in peak operating condition, resulting in a longer service life.

In summary, the Poulan 190785 stands out as a well-rounded chainsaw option, combining power, safety, and ease of use. Whether you are a homeowner looking to maintain your yard or a professional needing a reliable tool for forestry work, the Poulan 190785 delivers performance and efficiency to get the job done effectively. Its durable construction and thoughtful features make it a worthwhile investment for anyone seeking a chainsaw they can count on.
Top Page Image Contents