Poulan 184581 To Adjust Gauge Wheels See Fig, To Operate on Hills, To Operate Mower See Fig

Page 12
Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

OPERATION

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 7)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•Remove retainer spring and clevis pin which secure each gauge wheel bar.

•

"ENGAGED" POSITION

ATTACHMENT LIFT LEVER HIGH POSITION

ATTACHMENT

 

CLUTCH LEVER

LOW

"DISENGAGED"

POSITION

POSITION

 

DEFLECTOR

SHIELD

FIG. 8

TO OPERATE ON HILLS

•Replace retainer spring into clevis pin.

•Be sure all gauge wheels are in the same setting.

IMPORTANT:BE SURETO READJUST GAUGEWHEELS IFYOU CHANGE THE CUTTING HEIGHT OF THE MOWER DECK.

RETAINER

SPRING

CLEVIS

PIN

FIG. 7

TO OPERATE MOWER (See Fig. 8)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Lower mower with attachment lift control.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.

12

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move motion control lever to neutral (N) position.

IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/ BRAKE PEDAL IS DEPRESSED.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Slowly move motion control lever to slowest setting.

•Make all turns slowly.

TO TRANSPORT (See Figs. 5 and 9)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

•Raise attachment lift to highest position with attachment lift control.

•Pull freewheel control out and into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

Page 11 Page 13
Image 12
Page 11 Page 13
Contents PD18H42STA Safety Rules Safety Rules Table of Contents Unassembled Parts Steering Wheel SeatGauge Wheel Slope SheetAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CAR- TONCheck Battery See Fig Assemble Gauge Wheels to Mower Deck See aTo SET UP Your Mower for Mulching To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate on HillsTo Operate Mower See Fig To Transport See FigsBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionMulching Mowing Tips Maintenance Lubrication ChartService Dates General RecommendationsTractor Engine Cleaning Engine OIL FilterMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Check and Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Transmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentFront Wheel TOE-IN/CAMBER Replacing Battery See Figs To Remove Hood and Grill Assembly See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable See Fig To Adjust Carburetor See FigAcceleration Test Storage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PD18H42STA, Product no 56Tractor - Model Number PD18H42STA, Product no 56 Electrical KEY Part NO. NO. Description 159 KEY Part Description Tractor - Model Number PD18H42STA, Product no 56 Drive Repair Parts Repair Parts 180656 Wheel Steering Tractor - Model Number PD18H42STA, Product no 56 Engine KEY Part NO. NO. Description KEY Part Description Tractor - Model Number PD18H42STA, Product no 56 Decals Wheels & TiresTractor - Model Number PD18H42STA, Product no 56 Mower Lift Repair Parts Tractor - Model Number PD18H42STA, Product no 56 Mower Deck 152 153 154182032X421 Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

184581 specifications

The Poulan 184581 is a powerful and versatile chainsaw designed for both professional and casual users. Known for its reliability and performance, this model is an excellent choice for those who seek efficiency in cutting through various types of wood, whether for clearing trails, cutting firewood, or tackling larger landscaping projects.

One of the standout features of the Poulan 184581 is its engine. With a robust and efficient engine that boasts a displacement of over 40cc, this chainsaw offers significant cutting power. Its 2-stroke engine is designed to deliver a balanced blend of performance and fuel efficiency, allowing users to maximize their working time without frequent refueling. The engine is equipped with a primer bulb and choke for easier starting, ensuring that even those who are less experienced can quickly get the chainsaw up and running.

Another notable aspect of the Poulan 184581 is its lightweight design. Weighing just over 10 pounds, this chainsaw is manageable for extended periods, reducing user fatigue, especially during prolonged use. Despite its lightweight nature, the chainsaw does not compromise on durability. Constructed from high-quality materials, it can withstand the rigors of outdoor operations, making it a reliable tool for various applications.

The Poulan 184581 incorporates advanced features for user safety and ease of use. It has a chain brake that instantly stops the chain in the event of kickback, a critical safety feature for both novice and seasoned users. The automatic oiling system ensures that the chain receives consistent lubrication during operation, reducing wear and tear while enhancing cutting efficiency.

This chainsaw is equipped with a 20-inch bar, providing a good balance between maneuverability and cutting capacity. The length is ideal for tackling medium to large-sized trees and branches while still allowing for precision when making detailed cuts. The chain is designed for easy sharpening and replacement, ensuring that maintenance is straightforward.

In terms of user comfort, the Poulan 184581 features an ergonomic handle that provides a secure grip, promoting better control during cutting tasks. The anti-vibration technology helps to reduce vibrations felt by the user, making it easier to maintain a steady hand and reduce fatigue throughout the day.

Overall, the Poulan 184581 is a compelling choice for anyone in need of a reliable chainsaw. Its combination of power, lightweight design, safety features, and ease of use make it a valuable addition to any toolbox, whether for professional use or home gardening projects.
Top Page Image Contents