Poulan 184581 owner manual To Level Mower Housing, FRONT-TO-BACK Adjustment See Figs

Page 21

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 19 and 20)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE OF

BOTTOM EDGE OF

MOWER TO GROUND

MOWER TO GROUND

“A”

GROUND LINE

“A”

FIG. 19

SUSPENSION ARM

LIFT LINK ADJUSTMENT NUT

FIG. 20

FRONT-TO-BACK ADJUSTMENT (See Figs. 21 and 22)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

"D"

"D"

FIG. 21

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT "F"

NUT "E"

TRUNNION

FRONT LINKS

FIG. 22

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents PD18H42STA Safety Rules Safety Rules Table of Contents Steering Wheel Seat Unassembled PartsGauge Wheel Slope SheetTools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CAR- TONAssemble Gauge Wheels to Mower Deck See a Check Battery See FigTo Convert to Bagging or Discharging To SET UP Your Mower for MulchingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Transport See FigsTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsMulching Mowing Tips Lubrication Chart MaintenanceService Dates General RecommendationsTractor Engine Engine OIL Filter CleaningMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Check and Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Transmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentFront Wheel TOE-IN/CAMBER To Remove Hood and Grill Assembly See Fig Replacing Battery See FigsTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable See Fig To Adjust Carburetor See FigAcceleration Test Other StorageFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number PD18H42STA, Product no 56 SchematicTractor - Model Number PD18H42STA, Product no 56 Electrical KEY Part NO. NO. Description 159 KEY Part Description Tractor - Model Number PD18H42STA, Product no 56 Drive Repair Parts Repair Parts 180656 Wheel Steering Tractor - Model Number PD18H42STA, Product no 56 Engine KEY Part NO. NO. Description KEY Part Description Wheels & Tires Tractor - Model Number PD18H42STA, Product no 56 DecalsTractor - Model Number PD18H42STA, Product no 56 Mower Lift Repair Parts 152 153 154 Tractor - Model Number PD18H42STA, Product no 56 Mower Deck182032X421 Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

184581 specifications

The Poulan 184581 is a powerful and versatile chainsaw designed for both professional and casual users. Known for its reliability and performance, this model is an excellent choice for those who seek efficiency in cutting through various types of wood, whether for clearing trails, cutting firewood, or tackling larger landscaping projects.

One of the standout features of the Poulan 184581 is its engine. With a robust and efficient engine that boasts a displacement of over 40cc, this chainsaw offers significant cutting power. Its 2-stroke engine is designed to deliver a balanced blend of performance and fuel efficiency, allowing users to maximize their working time without frequent refueling. The engine is equipped with a primer bulb and choke for easier starting, ensuring that even those who are less experienced can quickly get the chainsaw up and running.

Another notable aspect of the Poulan 184581 is its lightweight design. Weighing just over 10 pounds, this chainsaw is manageable for extended periods, reducing user fatigue, especially during prolonged use. Despite its lightweight nature, the chainsaw does not compromise on durability. Constructed from high-quality materials, it can withstand the rigors of outdoor operations, making it a reliable tool for various applications.

The Poulan 184581 incorporates advanced features for user safety and ease of use. It has a chain brake that instantly stops the chain in the event of kickback, a critical safety feature for both novice and seasoned users. The automatic oiling system ensures that the chain receives consistent lubrication during operation, reducing wear and tear while enhancing cutting efficiency.

This chainsaw is equipped with a 20-inch bar, providing a good balance between maneuverability and cutting capacity. The length is ideal for tackling medium to large-sized trees and branches while still allowing for precision when making detailed cuts. The chain is designed for easy sharpening and replacement, ensuring that maintenance is straightforward.

In terms of user comfort, the Poulan 184581 features an ergonomic handle that provides a secure grip, promoting better control during cutting tasks. The anti-vibration technology helps to reduce vibrations felt by the user, making it easier to maintain a steady hand and reduce fatigue throughout the day.

Overall, the Poulan 184581 is a compelling choice for anyone in need of a reliable chainsaw. Its combination of power, lightweight design, safety features, and ease of use make it a valuable addition to any toolbox, whether for professional use or home gardening projects.
Top Page Image Contents