Poulan 184581 owner manual Tools Required for Assembly, To Remove Tractor from CAR- TON

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

Utility knife

Pliers

(1)

3/4" wrenches

Tire pressure gauge

(2)

7/16" wrenches

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CAR- TON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton .

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 1/4 hex bolt and locknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 10-12 FT. LBS TORQUE.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•

Position front wheels of the tractor so they are pointing straight

 

forward.

•

Remove steering wheel adapter from steering wheel and

STEERING

WHEEL

ADAPTER

1/4 LOCKNUT

LOWER

STEERING

SHAFT

INSERT

1/2 HEX NUT

LARGE FLAT

WASHER

STEERING

BOOT

TABS

EXTENSION SHAFT

1/4 HEX BOLT

TAB

SLOTS

 

slide adapter onto steering shaft extension.

•

Position steering wheel so cross bars are horizontal (left to

 

right) and slide inside boot and onto adapter.

•

Assemble large flat washer, 1/2 hex nut and tighten se-

 

curely.

•

Snap steering wheel insert into center of steering wheel.

•

Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

FIG. 1

HOW TO SET UP YOUR TRACTOR

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment knob.

• Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

• Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

• Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

• Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

• Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

• Lower seat into operating position and sit on seat.

• Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the

6

way down.

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PD18H42STA Safety Rules Safety Rules Table of Contents Gauge Wheel Unassembled PartsSteering Wheel Seat Slope SheetHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CAR- TONCheck Battery See Fig Assemble Gauge Wheels to Mower Deck See aCheck Tire Pressure To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsCheck Engine OIL Level Before Starting the EngineTowing Carts and Other ATTACH- Ments ADD GasolineMowing Tips Purge TransmissionMulching Mowing Tips Service Dates MaintenanceLubrication Chart General RecommendationsTractor Engine Muffler CleaningEngine OIL Filter Spark PlugsService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Check and Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Transmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentFront Wheel TOE-IN/CAMBER To Replace Headlight Bulb Replacing Battery See FigsTo Remove Hood and Grill Assembly See Fig Interlocks and RelaysTo Adjust Throttle Control Cable See Fig To Adjust Carburetor See FigAcceleration Test Fuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PD18H42STA, Product no 56Tractor - Model Number PD18H42STA, Product no 56 Electrical KEY Part NO. NO. Description 159 KEY Part Description Tractor - Model Number PD18H42STA, Product no 56 Drive Repair Parts Repair Parts 180656 Wheel Steering Tractor - Model Number PD18H42STA, Product no 56 Engine KEY Part NO. NO. Description KEY Part Description Tractor - Model Number PD18H42STA, Product no 56 Decals Wheels & TiresTractor - Model Number PD18H42STA, Product no 56 Mower Lift Repair Parts Tractor - Model Number PD18H42STA, Product no 56 Mower Deck 152 153 154182032X421 Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

184581 specifications

The Poulan 184581 is a powerful and versatile chainsaw designed for both professional and casual users. Known for its reliability and performance, this model is an excellent choice for those who seek efficiency in cutting through various types of wood, whether for clearing trails, cutting firewood, or tackling larger landscaping projects.

One of the standout features of the Poulan 184581 is its engine. With a robust and efficient engine that boasts a displacement of over 40cc, this chainsaw offers significant cutting power. Its 2-stroke engine is designed to deliver a balanced blend of performance and fuel efficiency, allowing users to maximize their working time without frequent refueling. The engine is equipped with a primer bulb and choke for easier starting, ensuring that even those who are less experienced can quickly get the chainsaw up and running.

Another notable aspect of the Poulan 184581 is its lightweight design. Weighing just over 10 pounds, this chainsaw is manageable for extended periods, reducing user fatigue, especially during prolonged use. Despite its lightweight nature, the chainsaw does not compromise on durability. Constructed from high-quality materials, it can withstand the rigors of outdoor operations, making it a reliable tool for various applications.

The Poulan 184581 incorporates advanced features for user safety and ease of use. It has a chain brake that instantly stops the chain in the event of kickback, a critical safety feature for both novice and seasoned users. The automatic oiling system ensures that the chain receives consistent lubrication during operation, reducing wear and tear while enhancing cutting efficiency.

This chainsaw is equipped with a 20-inch bar, providing a good balance between maneuverability and cutting capacity. The length is ideal for tackling medium to large-sized trees and branches while still allowing for precision when making detailed cuts. The chain is designed for easy sharpening and replacement, ensuring that maintenance is straightforward.

In terms of user comfort, the Poulan 184581 features an ergonomic handle that provides a secure grip, promoting better control during cutting tasks. The anti-vibration technology helps to reduce vibrations felt by the user, making it easier to maintain a steady hand and reduce fatigue throughout the day.

Overall, the Poulan 184581 is a compelling choice for anyone in need of a reliable chainsaw. Its combination of power, lightweight design, safety features, and ease of use make it a valuable addition to any toolbox, whether for professional use or home gardening projects.
Top Page Image Contents