Poulan 184581 To Replace Headlight Bulb, Interlocks and Relays, Replacing Battery See Figs

Page 24

SERVICE AND ADJUSTMENTS

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

SEAT PAN

 

FIG. 29

TERMINAL COVER

KEPS NUT

 

HEX BOLT

POSITIVE (RED) CABLE

NEGATIVE (BLACK) CABLE

FIG. 30

TO REPLACE HEADLIGHT BULB

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

FIG. 28

REPLACING BATTERY (See Figs. 29 and 30)

WARNING: Do not short battery ter- minals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acci- dental grounding.

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 31)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT WIRE

CONNECTOR

FIG. 31

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents PD18H42STA Safety Rules Safety Rules Table of Contents Unassembled Parts Steering Wheel SeatGauge Wheel Slope SheetAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CAR- TONCheck Battery See Fig Assemble Gauge Wheels to Mower Deck See aTo SET UP Your Mower for Mulching To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate on HillsTo Operate Mower See Fig To Transport See FigsBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionMulching Mowing Tips Maintenance Lubrication ChartService Dates General RecommendationsTractor Engine Cleaning Engine OIL FilterMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Check and Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Transmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentFront Wheel TOE-IN/CAMBER Replacing Battery See Figs To Remove Hood and Grill Assembly See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable See Fig To Adjust Carburetor See FigAcceleration Test Storage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PD18H42STA, Product no 56Tractor - Model Number PD18H42STA, Product no 56 Electrical KEY Part NO. NO. Description 159 KEY Part Description Tractor - Model Number PD18H42STA, Product no 56 Drive Repair Parts Repair Parts 180656 Wheel Steering Tractor - Model Number PD18H42STA, Product no 56 Engine KEY Part NO. NO. Description KEY Part Description Tractor - Model Number PD18H42STA, Product no 56 Decals Wheels & TiresTractor - Model Number PD18H42STA, Product no 56 Mower Lift Repair Parts Tractor - Model Number PD18H42STA, Product no 56 Mower Deck 152 153 154182032X421 Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

184581 specifications

The Poulan 184581 is a powerful and versatile chainsaw designed for both professional and casual users. Known for its reliability and performance, this model is an excellent choice for those who seek efficiency in cutting through various types of wood, whether for clearing trails, cutting firewood, or tackling larger landscaping projects.

One of the standout features of the Poulan 184581 is its engine. With a robust and efficient engine that boasts a displacement of over 40cc, this chainsaw offers significant cutting power. Its 2-stroke engine is designed to deliver a balanced blend of performance and fuel efficiency, allowing users to maximize their working time without frequent refueling. The engine is equipped with a primer bulb and choke for easier starting, ensuring that even those who are less experienced can quickly get the chainsaw up and running.

Another notable aspect of the Poulan 184581 is its lightweight design. Weighing just over 10 pounds, this chainsaw is manageable for extended periods, reducing user fatigue, especially during prolonged use. Despite its lightweight nature, the chainsaw does not compromise on durability. Constructed from high-quality materials, it can withstand the rigors of outdoor operations, making it a reliable tool for various applications.

The Poulan 184581 incorporates advanced features for user safety and ease of use. It has a chain brake that instantly stops the chain in the event of kickback, a critical safety feature for both novice and seasoned users. The automatic oiling system ensures that the chain receives consistent lubrication during operation, reducing wear and tear while enhancing cutting efficiency.

This chainsaw is equipped with a 20-inch bar, providing a good balance between maneuverability and cutting capacity. The length is ideal for tackling medium to large-sized trees and branches while still allowing for precision when making detailed cuts. The chain is designed for easy sharpening and replacement, ensuring that maintenance is straightforward.

In terms of user comfort, the Poulan 184581 features an ergonomic handle that provides a secure grip, promoting better control during cutting tasks. The anti-vibration technology helps to reduce vibrations felt by the user, making it easier to maintain a steady hand and reduce fatigue throughout the day.

Overall, the Poulan 184581 is a compelling choice for anyone in need of a reliable chainsaw. Its combination of power, lightweight design, safety features, and ease of use make it a valuable addition to any toolbox, whether for professional use or home gardening projects.
Top Page Image Contents