Poulan 187007 manual Tractor, Brake Operation, Tires, Operator Presence System, Blade Care

Page 15

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 8)

•Raise mower to highest position to allow access to blades.

•Remove blade bolt, lock washer and flat washer securing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble blade bolt, lock washer and flat washer in exact order as shown.

•Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

MANDREL

TRAILINGASSEMBLY EDGE UP

CENTER

HOLE

LOCK WASHER

STAR

FLAT WASHER

BLADE

 

BLADE BOLT (GRADE 8)*

*A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 8

TO SHARPEN BLADE (See Fig. 9)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An un- balanced blade will cause excessive vibration and eventual damage to mower and engine.

•The blade can be sharpened with a file or on a grind- ing wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

CENTER HOLE

5/8" BOLT

BLADE

OR PIN

 

FIG. 9

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model NO. PO13T38A II. Slope Operation Safety RulesIV. Service General OperationSafety Rules Table of Contents Steering Wheel Seat Unassembled PartsBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonHOW to SET UP Your Tractor Install Seat See FigCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Check Engine OIL Level Before Starting the EngineTo Operate on Hills To Transport Towing Carts and Other ATTACH- MentsTo Start Engine See Fig Mowing TipsBefore Each USE MaintenanceLubrication Chart General RecommendationsOperator Presence System TractorBrake Operation TiresEngine IN-LINE Fuel Filter See Fig CleaningMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake See FigTo Remove Wheel for Repairs See Fig To Adjust Steering Wheel ALIGN- MentTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBERReplacing Battery See Figs To Start Engine with a Weak Battery See FigInterlocks and Relays To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number PO13T38A SchematicElectrical KEY Part Description Chassis Repair Parts Drive KEY Part NO. NO. Description Steering Repair Parts Engine KEY Part NO. NO. Description Seat Wheels & Tires DecalsMower Lift Repair Parts Mower Deck 178515 Service Notes Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

187007 specifications

The Poulan 187007 is a powerful and reliable chainsaw designed for both residential and professional use. With its ergonomic design and advanced technology, it stands out in the competitive market of outdoor tools.

One of the key features of the Poulan 187007 is its robust engine. It is equipped with a 46cc two-stroke engine that delivers a significant amount of power, making it suitable for a variety of tasks such as tree trimming, firewood cutting, and storm cleanup. The engine's efficient design not only ensures high performance but also minimizes fuel consumption, allowing users to work longer without frequent refueling.

In terms of safety, the Poulan 187007 comes with several features designed to protect the user. The chainsaw is equipped with a chain brake that can be activated manually or automatically, reducing the risk of kickback injuries. Additionally, its anti-vibration technology helps to dampen the vibrations produced during operation, offering comfort to the user and reducing fatigue over extended periods of use.

The Poulan 187007 also boasts an easy-start system. This technology allows for smooth and effortless starting, which can be particularly beneficial when starting in cold weather or after long periods of inactivity. The tool’s adjustable oil flow system ensures that the chain remains lubricated, extending its lifespan and enhancing cutting efficiency.

Another noteworthy characteristic is its lightweight design. Weighing in at just under 13 pounds, the Poulan 187007 is easy to maneuver, making it a great option for both novice users and experienced professionals. The balanced weight distribution and comfortable handle grip further enhance the user experience, allowing for greater control while cutting.

Durability is a hallmark of the Poulan brand, and the 187007 is no exception. Constructed with high-quality materials, this chainsaw is designed to withstand the rigors of regular use. Whether tackling dense wood or engaging in lighter yard work, it is built to last.

In summary, the Poulan 187007 is an excellent addition to any toolbox, combining power, safety, and reliability. Its array of features makes it suitable for tackling various outdoor tasks, providing users with a dependable and efficient tool. For those looking for a versatile chainsaw, the Poulan 187007 is a model worth considering.
Top Page Image Contents