Poulan 187007 manual To Level Mower Housing, FRONT-TO-BACK Adjustment See Figs

Page 19

SERVICE AND ADJUSTMENTS

•Push clutch cable housing guide into bracket, slide col- lar onto guide and secure with large retainer spring.

•Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring.

•Install belt onto engine pulley.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 14 and 15)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE OF

BOTTOM EDGE

MOWER

OF MOWER

TO GROUND

TO GROUND

“A”

“A”

 

GROUND LINE

FIG. 14

SUSPENSION ARM

LIFT LINK

ADJUSTMENT

NUT

FIG. 15

FRONT-TO-BACK ADJUSTMENT (See Figs. 16 and 17)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

"D"

"D"

FIG. 16

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT "F"

NUT "E"

TRUNNION

FRONT LINKS

FIG. 17

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model NO. PO13T38A II. Slope Operation Safety RulesIV. Service General OperationSafety Rules Table of Contents Steering Wheel Seat Unassembled PartsBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Check Engine OIL Level Before Starting the EngineTo Operate on Hills To Transport Towing Carts and Other ATTACH- MentsTo Start Engine See Fig Mowing TipsBefore Each USE MaintenanceLubrication Chart General RecommendationsOperator Presence System TractorBrake Operation TiresEngine IN-LINE Fuel Filter See Fig CleaningMuffler Spark PlugsTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake See FigTo Remove Wheel for Repairs See Fig To Adjust Steering Wheel ALIGN- MentTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBERReplacing Battery See Figs To Start Engine with a Weak Battery See FigInterlocks and Relays To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number PO13T38A SchematicElectrical KEY Part Description Chassis Repair Parts Drive KEY Part NO. NO. Description Steering Repair Parts Engine KEY Part NO. NO. Description Seat Wheels & Tires DecalsMower Lift Repair Parts Mower Deck 178515 Service Notes Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

187007 specifications

The Poulan 187007 is a powerful and reliable chainsaw designed for both residential and professional use. With its ergonomic design and advanced technology, it stands out in the competitive market of outdoor tools.

One of the key features of the Poulan 187007 is its robust engine. It is equipped with a 46cc two-stroke engine that delivers a significant amount of power, making it suitable for a variety of tasks such as tree trimming, firewood cutting, and storm cleanup. The engine's efficient design not only ensures high performance but also minimizes fuel consumption, allowing users to work longer without frequent refueling.

In terms of safety, the Poulan 187007 comes with several features designed to protect the user. The chainsaw is equipped with a chain brake that can be activated manually or automatically, reducing the risk of kickback injuries. Additionally, its anti-vibration technology helps to dampen the vibrations produced during operation, offering comfort to the user and reducing fatigue over extended periods of use.

The Poulan 187007 also boasts an easy-start system. This technology allows for smooth and effortless starting, which can be particularly beneficial when starting in cold weather or after long periods of inactivity. The tool’s adjustable oil flow system ensures that the chain remains lubricated, extending its lifespan and enhancing cutting efficiency.

Another noteworthy characteristic is its lightweight design. Weighing in at just under 13 pounds, the Poulan 187007 is easy to maneuver, making it a great option for both novice users and experienced professionals. The balanced weight distribution and comfortable handle grip further enhance the user experience, allowing for greater control while cutting.

Durability is a hallmark of the Poulan brand, and the 187007 is no exception. Constructed with high-quality materials, this chainsaw is designed to withstand the rigors of regular use. Whether tackling dense wood or engaging in lighter yard work, it is built to last.

In summary, the Poulan 187007 is an excellent addition to any toolbox, combining power, safety, and reliability. Its array of features makes it suitable for tackling various outdoor tasks, providing users with a dependable and efficient tool. For those looking for a versatile chainsaw, the Poulan 187007 is a model worth considering.
Top Page Image Contents