Poulan XT24H48YT manual Before Starting the Engine, To Transport See Figs, Check Engine OIL Level

Page 14

OPERATION

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move motion control lever to neutral (N) position.

IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/ BRAKE PEDAL IS DEPRESSED.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Slowly move motion control lever to slowest setting.

•Make all turns slowly.

TO TRANSPORT (See Figs. 6 and 10)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

•Raise attachment lift to highest position with attachment lift control.

•Pull freewheel control out and down into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

Transmission Engaged

Transmission Disengaged

FIG. 10

TOWING CARTS AND OTHER ATTACHMENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

•Check engine oil with tractor on level ground.

•Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Maintenance section of this manual).

•To change engine oil, see the Maintenance section in this manual.

ADD GASOLINE

•Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 6)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Be sure freewheel control is in the transmission engaged position.

•Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

•Place motion control lever in neutral (N) position.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to fast position

•Pull choke control out for a cold engine start attempt. For a warm engine start attempt the choke control may not be needed.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, push choke control in, wait a few minutes and try again. If engine still does not start, pull the choke control out and retry.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents XT24H48YT Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIV. Towing ServiceIII. Children Table of Contents Unassembled Parts To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsCheck Engine OIL Level Before Starting the EngineTo Transport See Figs ADD GasolineAutomatic Transmission Warm UP Mowing TipsPurge Transmission General Recommendations MaintenanceLubrication Chart Before Each USETo Sharpen Blade See Fig TractorBlade Removal See Fig Check Operator Presence SystemEngine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower To Level Mower Housing FRONT-TO-BACK Adjustment See FigsMower Drive Belt Installation To Replace Mower Drive BeltTo Check and Adjust Brake See Fig To Replace Mower Blade Secondary Drive Belt See FigTo Replace Motion Drive Belt See Fig Transaxle Motion Control Lever Neutral Adjustment See FigBelt Installation Belt RemovalFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment To Attach Jumper CablesTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points Engine dies when Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

XT24H48YT specifications

The Poulan XT24H48YT is a robust riding lawn mower, designed to tackle a variety of mowing tasks with efficiency and ease. This model is particularly well-suited for homeowners with medium to large yards, offering impressive power and maneuverability to get the job done effectively.

At the heart of the XT24H48YT is a dependable 24-horsepower Briggs & Stratton engine. This powerful engine provides the durability and reliability necessary for consistent performance over time. The engine is coupled with a hydrostatic transmission, which allows for smooth, automatic speed adjustments without the need for manual shifting. This feature enhances the overall ease of operation, particularly in larger or more complex terrains.

The cutting deck on the Poulan XT24H48YT measures 48 inches in width, which strikes an excellent balance between efficient grass cutting and ease of navigation in tighter spaces. The deck features a reinforced design, enabling it to withstand the rigors of frequent use. Additionally, the mower comes equipped with a cutting height adjustment feature that allows users to customize their mowing height across six different positions, ensuring the best results for various grass types and conditions.

One of the standout features of the Poulan XT24H48YT is its ergonomically designed seat and controls. The high-back seat offers ample support and comfort during extended mowing sessions, while the user-friendly steering system contributes to easy handling and maneuverability. The mower also includes a tight turning radius, allowing users to navigate around landscaping obstacles and corners with ease.

In terms of additional technologies, the Poulan XT24H48YT sports a variety of practical features such as a built-in headlight for improved visibility during early morning or late evening mowing. Furthermore, the model has a durable outer chassis constructed from high-quality materials, ensuring it can withstand the elements and rough terrains.

Maintenance is made simpler with the addition of an easy-access hose connection for cleaning the cutting deck, helping to keep the mower in excellent condition without extensive effort. The Poulan XT24H48YT is also compatible with various lawn care accessories, providing versatility and the ability to adapt the machine to different seasonal tasks.

Overall, the Poulan XT24H48YT combines power, comfort, and versatility, making it a compelling choice for homeowners seeking an effective riding lawn mower that can handle a variety of mowing tasks with ease. Its thoughtful design and features ensure that lawn care remains a manageable and pleasant chore.
Top Page Image Contents