Poulan XT24H48YT Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

3/4" wrench

Pliers

(1)

9/16" wrench

Tire pressure gauge

 

 

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Remove mower and packing materials.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

•Remove locknut and large flat washer from steering shaft.

•Position front wheels of the tractor so they are pointing straight forward.

•Slide the steering sleeve over the steering shaft.

•Position steering wheel so cross bars are horizontal (left to right) and slide onto steering wheel adapter.

•Secure steering wheel to steering shaft with locknut and large flat washer previously removed. Tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

STEERING WHEEL

INSERT

LOCK NUT

LARGE FLAT WASHER

STEERING WHEEL

STEERING WHEEL ADAP- TOR

STEERING

SHAFT

STEERING

SLEEVE

 

 

 

8

 

 

1

 

8

 

2

 

 

0

 

 

 

FIG. 1

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents XT24H48YT Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationService III. ChildrenIV. Towing Table of Contents Unassembled Parts To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsCheck Engine OIL Level Before Starting the EngineTo Transport See Figs ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP General Recommendations MaintenanceLubrication Chart Before Each USETo Sharpen Blade See Fig TractorBlade Removal See Fig Check Operator Presence SystemEngine Cleaning Service and Adjustments To Install MowerTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsMower Drive Belt Installation To Replace Mower Drive BeltTo Check and Adjust Brake See Fig To Replace Mower Blade Secondary Drive Belt See FigTo Replace Motion Drive Belt See Fig Transaxle Motion Control Lever Neutral Adjustment See FigBelt Installation Belt RemovalFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment To Attach Jumper CablesTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points Engine dies when Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

XT24H48YT specifications

The Poulan XT24H48YT is a robust riding lawn mower, designed to tackle a variety of mowing tasks with efficiency and ease. This model is particularly well-suited for homeowners with medium to large yards, offering impressive power and maneuverability to get the job done effectively.

At the heart of the XT24H48YT is a dependable 24-horsepower Briggs & Stratton engine. This powerful engine provides the durability and reliability necessary for consistent performance over time. The engine is coupled with a hydrostatic transmission, which allows for smooth, automatic speed adjustments without the need for manual shifting. This feature enhances the overall ease of operation, particularly in larger or more complex terrains.

The cutting deck on the Poulan XT24H48YT measures 48 inches in width, which strikes an excellent balance between efficient grass cutting and ease of navigation in tighter spaces. The deck features a reinforced design, enabling it to withstand the rigors of frequent use. Additionally, the mower comes equipped with a cutting height adjustment feature that allows users to customize their mowing height across six different positions, ensuring the best results for various grass types and conditions.

One of the standout features of the Poulan XT24H48YT is its ergonomically designed seat and controls. The high-back seat offers ample support and comfort during extended mowing sessions, while the user-friendly steering system contributes to easy handling and maneuverability. The mower also includes a tight turning radius, allowing users to navigate around landscaping obstacles and corners with ease.

In terms of additional technologies, the Poulan XT24H48YT sports a variety of practical features such as a built-in headlight for improved visibility during early morning or late evening mowing. Furthermore, the model has a durable outer chassis constructed from high-quality materials, ensuring it can withstand the elements and rough terrains.

Maintenance is made simpler with the addition of an easy-access hose connection for cleaning the cutting deck, helping to keep the mower in excellent condition without extensive effort. The Poulan XT24H48YT is also compatible with various lawn care accessories, providing versatility and the ability to adapt the machine to different seasonal tasks.

Overall, the Poulan XT24H48YT combines power, comfort, and versatility, making it a compelling choice for homeowners seeking an effective riding lawn mower that can handle a variety of mowing tasks with ease. Its thoughtful design and features ensure that lawn care remains a manageable and pleasant chore.
Top Page Image Contents