Poulan XT24H48YT manual Transmission REMOVAL/REPLACEMENT, To Adjust Steering Wheel ALIGN- Ment

Page 25

SERVICE AND ADJUSTMENTS

MOTION CONTROL

NEUTRAL

LEVER

LOCK GATE

 

ADJUSTMENT

BOLT

FIG. 26

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See“PURGETRANSMISSION” in the Operation section of this manual.

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor.If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 27)

TO START ENGINE WITH A WEAK BATTERY (See Fig. 28)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 27

FIG. 28

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Always Wear EYE Protection During Operation XT24H48YTSafe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationIII. Children ServiceIV. Towing Table of Contents Unassembled Parts Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidAssemble Gauge Wheels to Mower Deck See Fig Check Battery See FigInstall Mower and Drive Belt See Figs Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigReverse Operation System ROS To Operate on HillsTo Transport See Figs Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP Lubrication Chart MaintenanceGeneral Recommendations Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Check Operator Presence SystemEngine Cleaning To Install Mower Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Drive Belt Mower Drive Belt InstallationTo Replace Mower Blade Secondary Drive Belt See Fig To Check and Adjust Brake See FigBelt Installation Transaxle Motion Control Lever Neutral Adjustment See FigTo Replace Motion Drive Belt See Fig Belt RemovalTo Adjust Steering Wheel ALIGN- Ment Transmission REMOVAL/REPLACEMENTFront Wheel TOE-IN/CAMBER To Attach Jumper CablesTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace FuseOther StorageFuel System Engine OILTroubleshooting Points Engine dies when Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

XT24H48YT specifications

The Poulan XT24H48YT is a robust riding lawn mower, designed to tackle a variety of mowing tasks with efficiency and ease. This model is particularly well-suited for homeowners with medium to large yards, offering impressive power and maneuverability to get the job done effectively.

At the heart of the XT24H48YT is a dependable 24-horsepower Briggs & Stratton engine. This powerful engine provides the durability and reliability necessary for consistent performance over time. The engine is coupled with a hydrostatic transmission, which allows for smooth, automatic speed adjustments without the need for manual shifting. This feature enhances the overall ease of operation, particularly in larger or more complex terrains.

The cutting deck on the Poulan XT24H48YT measures 48 inches in width, which strikes an excellent balance between efficient grass cutting and ease of navigation in tighter spaces. The deck features a reinforced design, enabling it to withstand the rigors of frequent use. Additionally, the mower comes equipped with a cutting height adjustment feature that allows users to customize their mowing height across six different positions, ensuring the best results for various grass types and conditions.

One of the standout features of the Poulan XT24H48YT is its ergonomically designed seat and controls. The high-back seat offers ample support and comfort during extended mowing sessions, while the user-friendly steering system contributes to easy handling and maneuverability. The mower also includes a tight turning radius, allowing users to navigate around landscaping obstacles and corners with ease.

In terms of additional technologies, the Poulan XT24H48YT sports a variety of practical features such as a built-in headlight for improved visibility during early morning or late evening mowing. Furthermore, the model has a durable outer chassis constructed from high-quality materials, ensuring it can withstand the elements and rough terrains.

Maintenance is made simpler with the addition of an easy-access hose connection for cleaning the cutting deck, helping to keep the mower in excellent condition without extensive effort. The Poulan XT24H48YT is also compatible with various lawn care accessories, providing versatility and the ability to adapt the machine to different seasonal tasks.

Overall, the Poulan XT24H48YT combines power, comfort, and versatility, making it a compelling choice for homeowners seeking an effective riding lawn mower that can handle a variety of mowing tasks with ease. Its thoughtful design and features ensure that lawn care remains a manageable and pleasant chore.
Top Page Image Contents